| *1 | SIDE GEAR | *2 | STRAIGHT PIN |
| *3 | PINION SHAFT | *4 | PINION GEAR |
| *5 | PINION GEAR THRUST WASHER | *6 | REAR NO. 1 DIFFERENTIAL SIDE GEAR THRUST WASHER |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
Hypoid gear oil | ★ | Precoated part |
| *1 | ADJUST SHIM | *2 | PLATE WASHER |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
MP grease |
|
Hypoid gear oil LSD | *T1 | 457 N*m (4660 kgf*cm, 337 ft.*lbf) or less |
1.ASSEMBLE DIFFERENTIAL CASE
Install the rear No. 1 differential side gear thrust washer to the side gear.
Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 41361-60K00 | 1.53 to 1.57 (0.0603 to 0.0618) | 41361-60K50 | 1.78 to 1.82 (0.0701 to 0.0716) |
| 41361-60K10 | 1.58 to 1.62 (0.0622 to 0.0637) | 41361-60K60 | 1.83 to 1.87 (0.0721 to 0.0736) |
| 41361-60K20 | 1.63 to 1.67 (0.0642 to 0.0657) | 41361-60K70 | 1.88 to 1.92 (0.0741 to 0.0755) |
| 41361-60K30 | 1.68 to 1.72 (0.0662 to 0.0677) | 41361-60K80 | 1.93 to 1.97 (0.0760 to 0.0775) |
| 41361-60K40 | 1.73 to 1.77 (0.0682 to 0.0696) | - | - |
Install 2 side gears, 2 pinion gears, 2 rear No. 1 differential side gear thrust washers, 2 pinion gear thrust washers and the pinion shaft in the differential case.
Align the holes of the differential case and pinion shaft.
Measure the side gear backlash.
Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.
0.05 to 0.20 mm (0.00197 to 0.00787 in.)
If the backlash is not as specified, install 2 side gear thrust washers with different thicknesses.
Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.
Stake the differential case.
2.INSTALL DIFFERENTIAL RING GEAR
| *a | Matchmark | - | - |
Clean the contact surfaces of the differential case and differential ring gear.
Heat the differential ring gear in boiling water that is approximately 100°C (212°F).
Carefully remove the differential ring gear from the boiling water.
After the moisture on the differential ring gear has completely evaporated, quickly align the matchmarks on the differential ring gear and differential case and install the differential ring gear to the differential case.
After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and Temporarily install them.
Toyota Genuine Adhesive 1360K, Three Bond1360K or equivalent
Diametrically tighten the 12 bolts uniformly in several passes.
41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING (INNER)
Using SST and a press, press the 2 rear differential case bearings onto the differential case.
4.INSPECT DIFFERENTIAL RING GEAR RUNOUT
| *a | Matchmark | *b | 121 mm (4.76 in.) |
Install the differential case on the differential carrier, and install the 2 plate washers so that there is no play in the bearing.
Align the matchmarks on the differential bearing cap and differential carrier and Install the 2 differential bearing caps with the 4 bolts.
Using a dial indicator, measure the runout of the differential ring gear.
0.05 mm (0.00197 in.)
Remove the 2 differential bearing caps, 2 plate washers and differential case assembly.
41201B 5.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)
| *1 | Rear Drive Pinion Front Tapered Roller Bearing (Outer) | - | - |
Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.
41201A 6.INSTALL REAR DRIVE PINION REAR BEARING (OUTER)
| *1 | Rear Drive Pinion Rear Tapered Roller Bearing (Outer) | *2 | Adjust Shim |
Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.
First, install an adjust shim that has the same thickness as the removed adjust shim. After checking the tooth contact pattern, replace the adjust shim with one of a different thickness if necessary.
41201A 7.INSTALL REAR DRIVE PINION REAR BEARING (INNER)
Using SST and a press, press the rear drive pinion rear tapered roller bearing (inner) onto the differential drive pinion.
8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD
Install the differential drive pinion, rear drive pinion front tapered roller bearing (inner).
Install the rear differential drive pinion bearing spacer and rear differential carrier oil seal after adjusting the gear contact pattern.
Install the rear differential drive pinion oil slinger.
| *a | Turn | *b | Hold |
Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Adjust the drive pinion preload by tightening the drive pinion nut.
Using SST to hold the companion flange in place, slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).
457 N*m (4660 kgf*cm, 337 ft.*lbf) or less
As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.
Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.
Using a torque wrench, measure the preload.
| Bearing | Preload |
|---|---|
| New bearing | 0.75 to 2.02 N*m (8 to 20 kgf*cm, 7 to 17 in.*lbf) |
| Reused bearing | 0.73 to 1.83 N*m (8 to 18 kgf*cm, 7 to 16 in.*lbf) |
For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
Record the differential drive pinion preload for the total preload measurement.
9.INSTALL DIFFERENTIAL CASE ASSEMBLY
Place the 2 rear differential case bearings (outer) to their respective bearings.
Make sure the right and left races are not interchanged.
10.ADJUST DIFFERENTIAL RING GEAR BACKLASH
Install the plate washer to the RH side (teeth side).
Make sure that the differential ring gear has backlash.
Using a dial indicator, while holding the companion flange, measure the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
Refer to the backlash when selecting a plate washer for the RH side (teeth side).
Select a plate washer for the LH side (back side) so that there is no gap between the rear differential case bearing (outer) and differential case.
Using a plastic-faced hammer, install the plate washer to the LH side (back side).
Using a dial indicator, adjust the ring gear backlash until it is within the specification.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
There should be no clearance between the plate washer and case.
Make sure that there is ring gear backlash.
If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
11.ADJUST SIDE BEARING PRELOAD
After adjusting the backlash of the differential ring gear, remove the plate washer from the LH side (back side).
Using a micrometer, measure the thickness of the plate washer.
Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed plate washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.
Select a plate washer which can be pressed in 2/3 of the full amount with your finger.
Recheck the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-59183 | 2.07 to 2.09 (0.0815 to 0.0822) | 90564-59199 | 2.39 to 2.41 (0.0941 to 0.0948) |
| 90564-59184 | 2.09 to 2.11 (0.0823 to 0.0830) | 90564-59200 | 2.41 to 2.43 (0.0949 to 0.0956) |
| 90564-59185 | 2.11 to 2.13 (0.0831 to 0.0838) | 90564-59201 | 2.43 to 2.45 (0.0957 to 0.0964) |
| 90564-59186 | 2.13 to 2.15 (0.0839 to 0.0846) | 90564-59202 | 2.45 to 2.47 (0.0965 to 0.0972) |
| 90564-59187 | 2.15 to 2.17 (0.0847 to 0.0854) | 90564-59203 | 2.47 to 2.49 (0.0973 to 0.0980) |
| 90564-59188 | 2.17 to 2.19 (0.0855 to 0.0862) | 90564-59204 | 2.49 to 2.51 (0.0981 to 0.0988) |
| 90564-59189 | 2.19 to 2.21 (0.0863 to 0.0870) | 90564-59205 | 2.51 to 2.53 (0.0989 to 0.0996) |
| 90564-59190 | 2.21 to 2.23 (0.0871 to 0.0877) | 90564-59206 | 2.53 to 2.55 (0.0997 to 0.1003) |
| 90564-59191 | 2.23 to 2.25 (0.0878 to 0.0885) | 90564-59207 | 2.55 to 2.57 (0.1004 to 0.1011) |
| 90564-59192 | 2.25 to 2.27 (0.0886 to 0.0893) | 90564-59208 | 2.57 to 2.59 (0.1012 to 0.1019) |
| 90564-59193 | 2.27 to 2.29 (0.0894 to 0.0901) | 90564-59209 | 2.59 to 2.61 (0.1020 to 0.1027) |
| 90564-59194 | 2.29 to 2.31 (0.0902 to 0.0909) | 90564-59210 | 2.61 to 2.63 (0.1028 to 0.1035) |
| 90564-59195 | 2.31 to 2.33 (0.0910 to 0.0917) | 90564-59211 | 2.63 to 2.65 (0.1036 to 0.1043) |
| 90564-59196 | 2.33 to 2.35 (0.0918 to 0.0925) | 90564-59212 | 2.65 to 2.67 (0.1044 to 0.1051) |
| 90564-59197 | 2.35 to 2.37 (0.0926 to 0.0933) | 90564-59213 | 2.67 to 2.69 (0.1052 to 0.1059) |
| 90564-59198 | 2.37 to 2.39 (0.0934 to 0.0940) | - | - |
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-59214 | 2.05 to 2.07 (0.0807 to 0.0814) | 90564-59230 | 2.37 to 2.39 (0.0934 to 0.0940) |
| 90564-59215 | 2.07 to 2.09 (0.0815 to 0.0822) | 90564-59231 | 2.39 to 2.41 (0.0941 to 0.0948) |
| 90564-59216 | 2.09 to 2.11 (0.0823 to 0.0830) | 90564-59232 | 2.41 to 2.43 (0.0949 to 0.0956) |
| 90564-59217 | 2.11 to 2.13 (0.0831 to 0.0838) | 90564-59233 | 2.43 to 2.45 (0.0957 to 0.0964) |
| 90564-59218 | 2.13 to 2.15 (0.0839 to 0.0846) | 90564-59234 | 2.45 to 2.47 (0.0965 to 0.0972) |
| 90564-59219 | 2.15 to 2.17 (0.0847 to 0.0854) | 90564-59235 | 2.47 to 2.49 (0.0973 to 0.0980) |
| 90564-59220 | 2.17 to 2.19 (0.0855 to 0.0862) | 90564-59236 | 2.49 to 2.51 (0.0981 to 0.0988) |
| 90564-59221 | 2.19 to 2.21 (0.0863 to 0.0870) | 90564-59237 | 2.51 to 2.53 (0.0989 to 0.0996) |
| 90564-59222 | 2.21 to 2.23 (0.0871 to 0.0877) | 90564-59238 | 2.53 to 2.55 (0.0997 to 0.1003) |
| 90564-59223 | 2.23 to 2.25 (0.0878 to 0.0885) | 90564-59239 | 2.55 to 2.57 (0.1004 to 0.1011) |
| 90564-59224 | 2.25 to 2.27 (0.0886 to 0.0893) | 90564-59240 | 2.57 to 2.59 (0.1012 to 0.1019) |
| 90564-59225 | 2.27 to 2.29 (0.0894 to 0.0901) | 90564-59241 | 2.59 to 2.61 (0.1020 to 0.1027) |
| 90564-59226 | 2.29 to 2.31 (0.0902 to 0.0909) | 90564-59242 | 2.61 to 2.63 (0.1028 to 0.1035) |
| 90564-59227 | 2.31 to 2.33 (0.0910 to 0.0917) | 90564-59243 | 2.63 to 2.65 (0.1036 to 0.1043) |
| 90564-59228 | 2.33 to 2.35 (0.0918 to 0.0925) | 90564-59244 | 2.65 to 2.67 (0.1044 to 0.1051) |
| 90564-59229 | 2.35 to 2.37 (0.0926 to 0.0933) | 90564-59245 | 2.67 to 2.69 (0.1052 to 0.1059) |
12.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.
| Reduction Ratio | Bearing | Preload |
|---|---|---|
| 3.307 | New bearing | 0.98 to 2.57 N*m (10 to 27 kgf*cm, 9 to 22 in.*lbf) |
| Reused bearing | 0.98 to 2.34 N*m (10 to 23 kgf*cm, 9 to 20 in.*lbf) | |
| 4.300 | New bearing | 0.93 to 2.44 N*m (10 to 24 kgf*cm, 9 to 21 in.*lbf) |
| Reused bearing | 0.92 to 2.22 N*m (10 to 22 kgf*cm, 9 to 19 in.*lbf) |
If necessary, disassemble and inspect the differential.
13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.
Hold the companion flange firmly in place and rotate the differential ring gear in both directions.
| *A | Drive Side | *B | Coast Side |
| *a | Proper Contact | *b | Toe Contact |
| *c | Face Contact | *d | Select an adjusting washer that will shift the drive pinion closer to the ring gear. |
| *e | Heel Contact | *f | Flank Contact |
| *g | Select an adjusting washer that will shift the drive pinion away from the ring gear. | *h | Heel Contact |
| *i | Flank Contact | *j | Toe Contact |
| *k | Face Contact | - | - |
Inspect the tooth contact pattern.
If the teeth are not contacting properly, use the following chart to select a proper adjust shim.
| *1 | Adjust Shim | *2 | Rear Drive Pinion Rear Tapered Roller Bearing (Outer) |
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-76019 | 1.71 to 1.73 (0.0674 to 0.0681) | 90564-76031 | 1.95 to 1.97 (0.0768 to 0.0775) |
| 90564-76020 | 1.73 to 1.75 (0.0682 to 0.0688) | 90564-76032 | 1.97 to 1.99 (0.0776 to 0.0783) |
| 90564-76021 | 1.75 to 1.77 (0.0689 to 0.0696) | 90564-76033 | 1.99 to 2.01 (0.0784 to 0.0791) |
| 90564-76022 | 1.77 to 1.79 (0.0697 to 0.0704) | 90564-76034 | 2.01 to 2.03 (0.0792 to 0.0799) |
| 90564-76023 | 1.79 to 1.81 (0.0705 to 0.0712) | 90564-76035 | 2.03 to 2.05 (0.0780 to 0.0807) |
| 90564-76024 | 1.81 to 1.83 (0.0713 to 0.0720) | 90564-76036 | 2.05 to 2.07 (0.0808 to 0.0814) |
| 90564-76025 | 1.83 to 1.85 (0.0721 to 0.0728) | 90564-76037 | 2.07 to 2.09 (0.0815 to 0.0822) |
| 90564-76026 | 1.85 to 1.87 (0.0729 to 0.0736) | 90564-76038 | 2.09 to 2.11 (0.0823 to 0.0830) |
| 90564-76027 | 1.87 to 1.89 (0.0737 to 0.0744) | 90564-76039 | 2.11 to 2.13 (0.0831 to 0.0838) |
| 90564-76028 | 1.89 to 1.91 (0.0745 to 0.0751) | 90564-76040 | 2.13 to 2.15 (0.0839 to 0.0846) |
| 90564-76029 | 1.91 to 1.93 (0.0752 to 0.0759) | 90564-76041 | 2.15 to 2.17 (0.0847 to 0.0854) |
| 90564-76030 | 1.93 to 1.95 (0.0760 to 0.0767) | 90564-76042 | 2.17 to 2.19 (0.0855 to 0.0862) |
41214 16.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
41231 20.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
41201B 22.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)
41201A 24.INSTALL REAR DRIVE PINION REAR BEARING (OUTER)
| *1 | Rear Drive Pinion Rear Tapered Roller Bearing (Outer) | *2 | Adjust Shim |
Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.
41201B 25.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)
| *1 | Rear Drive Pinion Front Tapered Roller Bearing (Outer) | - | - |
Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.
41231 26.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
41201B 27.INSTALL REAR DRIVE PINION FRONT BEARING (INNER)
28.INSTALL DIFFERENTIAL DRIVE PINION
Using SST and a press, install the differential drive pinion.
29.INSTALL DIFFERENTIAL CASE ASSEMBLY
Place the 2 rear differential case bearings (outer) to their respective bearings.
Make sure the right and left races are not interchanged.
30.INSTALL DIFFERENTIAL BEARING CAP
| *a | Matchmark | - | - |
Install the 2 plate washers.
Align the matchmarks on the differential bearing cap and differential carrier.
Install the right and left differential bearing caps with the 4 bolts.
41214 31.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
41201C 32.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
41204 33.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
| *a | Turn | *b | Hold |
Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.
Using SST to hold the companion flange in place, install a new nut.
457 N*m (4660 kgf*cm, 337 ft.*lbf) or less
34.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.
Using a torque wrench, measure the total preload.
| Reduction Ratio | Bearing | Preload |
|---|---|---|
| 3.307 | New bearing | 1.24 to 2.83 N*m (13 to 28 kgf*cm, 11 to 25 in.*lbf) |
| Reused bearing | 1.24 to 2.60 N*m (13 to 26 kgf*cm, 11 to 23 in.*lbf) | |
| 4.300 | New bearing | 1.19 to 2.70 N*m (13 to 27 kgf*cm, 11 to 23 in.*lbf) |
| Reused bearing | 1.18 to 2.48 N*m (13 to 25 kgf*cm, 11 to 21 in.*lbf) |
If necessary, disassemble and inspect the differential.
35.INSPECT DIFFERENTIAL RING GEAR BACKLASH
Using a dial indicator, check the backlash of the differential ring gear.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.
Perform the measurement at 3 or more positions around the circumference of the ring gear.
41204 36.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
| *a | 36 mm (1.42 in.) | - | - |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| Runout | Maximum |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
37.STAKE DRIVE PINION NUT