The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear differential carrier oil seal removal/installation are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.
When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
| *a | Object Exceeding Weight Limit of Transmission Jack |
Be sure to perform this procedure with several people as the rear differential carrier assembly is very heavy.
Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
41110 1.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY
w/ Differential Lock:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)>REMOVAL
w/o Differential Lock:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)>REMOVAL
41110 2.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
41204 3.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
w/ Differential Lock:
w/ Differential Lock:
4.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR
w/ Differential Lock:
w/ Differential Lock:
5.INSPECT DIFFERENTIAL RING GEAR BACKLASH
w/ Differential Lock:
w/ Differential Lock:
6.INSPECT TOTAL PRELOAD
w/ Differential Lock:
w/ Differential Lock:
41204B 7.REMOVE REAR DRIVE PINION NUT
w/ Differential Lock:
w/ Differential Lock:
41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
w/ Differential Lock:
w/ Differential Lock:
41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
| *1 | Rear Differential Carrier Oil Seal |
| *2 | Rear Differential Drive Pinion Oil Slinger |
Using SST, remove the rear differential carrier oil seal.
41214 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
w/ Differential Lock:
w/o Differential Lock:
11.REMOVE WIRING HARNESS CONNECTOR (w/ Differential Lock)
12.REMOVE DIFFERENTIAL BEARING CAP
w/ Differential Lock:
w/o Differential Lock:
13.REMOVE DIFFERENTIAL CASE ASSEMBLY (for LSD)
41303E 14.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY (w/ Differential Lock)
15.REMOVE DIFFERENTIAL CASE ASSEMBLY (w/o Differential Lock)
84222Q 16.REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH (w/ Differential Lock)
17.REMOVE DIFFERENTIAL DRIVE PINION
w/ Differential Lock:
w/o Differential Lock:
41231 18.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
w/ Differential Lock:
w/o Differential Lock:
41201B 19.REMOVE REAR DRIVE PINION FRONT BEARING (INNER)
w/ Differential Lock:
w/o Differential Lock:
41201B 20.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
41201B 21.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
22.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD
w/ Differential Lock:
w/o Differential Lock:
23.INSTALL DIFFERENTIAL CASE ASSEMBLY (for LSD)
41303E 24.INSTALL ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY (w/ Differential Lock)
25.INSTALL DIFFERENTIAL CASE ASSEMBLY (w/o Differential Lock)
26.ADJUST DIFFERENTIAL RING GEAR BACKLASH
w/ Differential Lock:
w/o Differential Lock:
27.ADJUST SIDE BEARING PRELOAD
w/ Differential Lock:
w/o Differential Lock:
28.INSPECT TOTAL PRELOAD
w/ Differential Lock:
w/o Differential Lock:
29.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
w/ Differential Lock:
w/o Differential Lock:
41204B 30.REMOVE REAR DRIVE PINION NUT
w/ Differential Lock:
w/o Differential Lock:
41204 31.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
41214 32.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
w/ Differential Lock:
w/o Differential Lock:
33.REMOVE DIFFERENTIAL BEARING CAP
w/ Differential Lock:
w/o Differential Lock:
34.REMOVE DIFFERENTIAL CASE ASSEMBLY (for LSD)
41303E 35.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY (w/ Differential Lock)
36.REMOVE DIFFERENTIAL CASE ASSEMBLY (w/o Differential Lock)
37.REMOVE DIFFERENTIAL DRIVE PINION
w/ Differential Lock:
w/o Differential Lock:
41231 38.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
w/ Differential Lock:
w/o Differential Lock:
41201B 39.REMOVE REAR DRIVE PINION FRONT BEARING (INNER)
w/ Differential Lock:
w/o Differential Lock:
41201B 40.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
41201A 41.REMOVE REAR DRIVE PINION REAR BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
41201A 42.INSTALL REAR DRIVE PINION REAR BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
41201B 43.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)
w/ Differential Lock:
w/o Differential Lock:
41201B 44.INSTALL REAR DRIVE PINION FRONT BEARING (INNER)
w/ Differential Lock:
w/o Differential Lock:
41231 45.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
w/ Differential Lock:
w/o Differential Lock:
46.INSTALL DIFFERENTIAL DRIVE PINION
w/ Differential Lock:
w/o Differential Lock:
84222Q 47.INSTALL DIFFERENTIAL LOCK INDICATOR SWITCH (w/ Differential Lock)
48.INSTALL DIFFERENTIAL CASE ASSEMBLY (for LSD)
41303E 49.INSTALL ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY (w/ Differential Lock)
50.INSTALL DIFFERENTIAL CASE ASSEMBLY (w/o Differential Lock)
51.INSTALL WIRING HARNESS CONNECTOR (w/ Differential Lock)
52.INSTALL DIFFERENTIAL BEARING CAP
w/ Differential Lock:
w/o Differential Lock:
41214 53.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
w/ Differential Lock:
w/o Differential Lock:
41201C 54.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
| *a | Rear Differential Carrier Oil Seal Depth |
Using SST and a hammer, tap in a new rear differential carrier oil seal.
0 to 0.3 mm (0 to 0.0118 in.)
Apply MP grease to the lip of the rear differential carrier oil seal.
41204 55.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
56.INSPECT TOTAL PRELOAD
w/ Differential Lock:
w/o Differential Lock:
57.INSPECT DIFFERENTIAL RING GEAR BACKLASH
w/ Differential Lock:
w/o Differential Lock:
41204 58.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
59.STAKE DRIVE PINION NUT
w/ Differential Lock:
w/o Differential Lock:
41110 60.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
61.ADD DIFFERENTIAL OIL