Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473048 FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/o Differential Lock) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/o Differential Lock)  REMOVAL  


CAUTION / NOTICE / HINT

C457925N01
3.417,1.333 3.417,0.417 3.417,0.417 3.583,0.417 true 1.5,0.417 2,0.417 true 6.417,1.75 6.583,1.75 6.583,1.75 6.583,2.417 true 4.75,3.5 5.25,3.5 true 6.167,0.417 6,0.417 6,0.417 6,1 true 1.26,2.094 1.26,2.677 1.26,2.677 0.969,2.677 true 6.125,1.552 6.458,1.917 0.333,0.365 18 false 1 2.031,0.25 2.365,0.615 0.333,0.365 18 false 2 5.313,3.313 5.667,3.677 0.354,0.365 18 false 4 6.24,0.219 6.521,0.573 0.281,0.354 18 false 3 0.625,2.531 0.99,2.844 0.365,0.313 18 false 6 1.208,1.281 1.542,1.49 0.333,0.208 10 false x 3 4.021,0.24 4.375,0.563 0.354,0.323 18 false 5 4.208,4.448 4.542,4.656 0.333,0.208 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DRIVE SHAFT ASSEMBLY LH 43420 - - -
2 FRONT DRIVE SHAFT ASSEMBLY RH 43410 - - -
3 FRONT PROPELLER SHAFT ASSEMBLY 37140 - - -
4 REMOVE DIFFERENTIAL SUPPORT ASSEMBLY 52380E - - -
5 FRONT DIFFERENTIAL CARRIER ASSEMBLY 41110F (Click here) - -
6 REMOVE FRONT DIFFERENTIAL SUPPORT ASSEMBLY 52380D - - -

V103638

Do not apply lubricants to the threaded parts - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential carrier assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) -
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


Be sure to perform this procedure with several people as the front differential carrier assembly is very heavy.

·

Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 43420 1.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 2.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.

Use the same procedure described for the LH side.


Hide 37140 3.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 52380E 4.REMOVE DIFFERENTIAL SUPPORT ASSEMBLY

a.
C457933


Hide 41110F 5.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

a.
C457930


b.
C457931


c.
C457934C01
0.458,0.042 0.781,0.396 0.323,0.354 18 true i
V113147

Remove in this Direction - -


i.

Remove the 2 bolt, 2 nut and front differential carrier assembly shown in the illustlation.

CAUTION:

The front differential carrier assembly is a heavy component. Make sure that it is supported securely.


NOTICE:
·

Securely support the front differential carrier assembly while performing this step to avoid excessively tilting or dropping the front differential carrier assembly.

·

The remaining oil may leak out when removing the front differential carrier assembly.

·

Do not damage the installation surface when removing the front differential carrier assembly.

·

Remove the bolts with the front differential carrier assembly secured.





Hide 52380D 6.REMOVE FRONT DIFFERENTIAL SUPPORT ASSEMBLY

a.
C458511