Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B167587  C-Pillar Floor Cross Satellite Sensor Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B167587 C-Pillar Floor Cross Satellite Sensor Missing Message One of the following conditions is met:
·

A rear floor side airbag sensor malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Rear floor side airbag sensor

·

Floor side airbag sensor LH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C450171E29
1.594,0.677 1.75,0.875 0.156,0.198 10 false 2 1.583,1.479 1.74,1.677 0.156,0.198 10 false 1 2.854,0.656 3.01,0.854 0.156,0.198 10 false 1 2.844,1.479 3,1.677 0.156,0.198 10 false 2 4.146,0.667 4.302,0.865 0.156,0.198 10 false 4 5.333,0.656 5.646,0.854 0.313,0.198 10 false 28 5.365,1.49 5.677,1.688 0.313,0.198 10 false 29 4.177,1.49 4.333,1.688 0.156,0.198 10 false 3 5.635,0.813 6.25,1.01 0.615,0.198 10 false BCL+ 5.635,1.573 6.25,1.771 0.615,0.198 10 false BCL- 0.094,2.198 0.406,2.396 0.313,0.198 10 false S4 0.104,2.365 2.573,2.594 2.469,0.229 10 false Rear Floor Side Airbag Sensor 2.698,2.208 3.01,2.406 0.313,0.198 10 false S3 2.688,2.365 5.229,2.583 2.542,0.219 10 false Floor Side Airbag Sensor LH 5.406,2.198 6.021,2.396 0.615,0.198 10 false S1 5.396,2.354 6.927,2.688 1.531,0.333 10 false Airbag ECU Assembly 3.052,0.781 3.667,0.979 0.615,0.198 10 false BFL+ 3.063,1.573 3.677,1.771 0.615,0.198 10 false BFL- 3.708,0.781 4.323,0.979 0.615,0.198 10 false BBL+ 3.708,1.583 4.323,1.781 0.615,0.198 10 false BBL- 1.094,0.792 1.708,0.99 0.615,0.198 10 false BFL+ 1.104,1.573 1.719,1.771 0.615,0.198 10 false BFL-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009287 and B167587 are output A
DTC B167587 is output B
DTC B009387 and B167587 are not output C



Post-procedure1

c.

None



A

B

2.CHECK CONNECTION OF CONNECTORS

C

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the rear floor side airbag sensor and floor side airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E441555C07
0.719,0.865 1.135,1.115 0.417,0.25 0.823,3.448 1.24,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.719,1.094 true 2.354,1.583 2.104,1.583 2.104,1.583 1.885,1.073 true 1.135,4.167 1.552,4.167 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.958,3.5 1.271,3.656 0.313,0.156 10 false S4 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.813,0.917 1.125,1.073 0.313,0.156 10 false S3 0.958,1.51 1.521,1.771 0.563,0.26 10 false BFL+ 2.417,1.5 2.979,1.76 0.563,0.26 10 false BFL- 2.406,2.927 2.969,3.188 0.563,0.26 10 false BFL+ 0.875,2.938 1.438,3.198 0.563,0.26 10 false BFL- 0.927,4.104 1.24,4.26 0.313,0.156 10 false *4
*1 Floor Side Airbag Sensor LH
*2 Rear Floor Side Airbag Sensor LH
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Rear Floor Side Airbag Sensor LH)


Disconnect the S3 floor side airbag sensor LH connector.


b.

Disconnect the S4 rear floor side airbag sensor connector.


c.

Using a service wire, connect terminals 2 (BFL+) and 1 (BFL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S3)Location & Routing

Click Connector(S3)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Floor Side Airbag Sensor LH

S3-1 (BFL+) - S3-2 (BFL-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

Disconnect the service wire from connector B.



OK

4.CHECK REAR FLOOR SIDE AIRBAG SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR FLOOR SIDE AIRBAG SENSOR
a.
B529883C12
0.969,1.521 1.24,1.719 0.271,0.198 10 false *1 2.323,1.531 2.594,1.729 0.271,0.198 10 false *2 1.646,1.271 1.917,1.469 0.271,0.198 10 false *3
*1 Rear Floor Side Airbag Sensor
*2 Floor Side Airbag Sensor LH
*3 Wire Harness


Connect the S3 floor side airbag sensor LH connector.


b.

Replace the rear floor side airbag sensor with a new one or known good one.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK REAR FLOOR SIDE AIRBAG SENSOR
5.CHECK REAR FLOOR SIDE AIRBAG SENSOR

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B167587 is output A
DTC B167587 is not output B


HINT:

Codes other than DTCs B167587 may be output at this time, but they are not related to this check.



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the rear floor side airbag sensor to their original positions and connect the connectors.



A

B