| *A | w/ Rear No. 2 Seat | *B | w/o Rear No. 2 Seat |
| *C | w/ Tonneau Cover | - | - |
| *A | w/o Rear No. 2 Seat | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/ Tonneau Cover |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 24 | REAR NO. 1 SEAT PROTECTOR | 71695S | - | - | - |
| 25 | REAR NO. 2 SEAT PROTECTOR | 71695T | - | - | - |
| 26 | REAR NO. 3 SEAT PROTECTOR | 71695Y | - | - | - |
| 27 | REAR NO. 4 SEAT PROTECTOR | 71F95 | - | - | - |
| 28 | FRONT FLOOR CARPET ASSEMBLY | 58510D | - | - | - |
| *A | w/o Rear No. 2 Seat | *B | w/ Rear Air Duct |
| *C | w/o Rear Air Duct | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear floor side airbag sensor removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
|
|
for 1GR-FE:
for V35A-FTS:
3.OPERATE REAR NO. 1 SEAT ASSEMBLY LH
4.OPERATE REAR NO. 1 SEAT ASSEMBLY RH
| *A | for 60/40 Split Seat Type RH Side | *B | for 40/20/40 Split Seat Type RH Side |
5.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
|
|
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>REMOVAL
64910M 6.REMOVE TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat, w/ Tonneau Cover)
58410B 9.REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
58418H 10.REMOVE REAR FLOOR REAR BOARD LH (w/o Rear No. 2 Seat)
58417B 11.REMOVE REAR FLOOR REAR BOARD RH (w/o Rear No. 2 Seat)
Use the same procedure described for the LH side.
64993 12.REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58574G 13.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
67918D 14.REMOVE REAR DOOR SCUFF PLATE LH
67917C 15.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
73233D 16.REMOVE OUTER LAP BELT ANCHOR COVER
|
|
Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>REMOVAL
73370C 17.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73360C 18.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
73570 19.REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73560 20.REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
62520B 22.REMOVE QUARTER TRIM PANEL ASSEMBLY LH
62510M 23.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
71695S 24.REMOVE REAR NO. 1 SEAT PROTECTOR
71695T 25.REMOVE REAR NO. 2 SEAT PROTECTOR
71695Y 26.REMOVE REAR NO. 3 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
71F95 27.REMOVE REAR NO. 4 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
58510D 28.REMOVE FRONT FLOOR CARPET ASSEMBLY
The illustrations are representative examples, and details may differ.
58439F 29.REMOVE DECK BOARD BRACKET REINFORCEMENT (w/o Rear No. 2 Seat, w/o Rear Air Duct)
58456H 30.REMOVE NO. 2 DECK FLOOR BRACKET (w/o Rear No. 2 Seat, w/o Rear Air Duct)
87212L 31.REMOVE REAR NO. 7 AIR DUCT (w/ Rear Air Duct)
58556C 32.REMOVE REAR FLOOR SILENCER (w/o Rear Air Duct)
89839A 33.REMOVE REAR FLOOR SIDE AIRBAG SENSOR COVER
|
Double-Sided Tape | - | - |
89837A 34.REMOVE REAR FLOOR SIDE AIRBAG SENSOR
| *a | Turns off | - | - |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Remove the bolt.
Loosen the bolt while holding the rear floor side airbag sensor because the rear floor side airbag sensor guide is easily damaged.
If the rear floor side airbag sensor has been dropped, replace it with a new one.
Disengage the guide and remove the rear floor side airbag sensor.
35.REMOVE CLIP
Perform this procedure only when replacement of the clip is necessary.