| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B003811 | Second Row Right Side Airbag Deployment Control Circuit Short to Ground | One of the following conditions is met:
·
The airbag ECU assembly detects a short circuit to ground signal in the rear side squib RH circuit for 0.5 seconds.
·
A rear seat airbag assembly RH malfunction.
·
An airbag ECU assembly malfunction. |
·
Wire harness
·
Rear seat airbag assembly RH
·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| DTC B003811 is output | A |
| Past DTC B003811 is output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the rear seat airbag assembly RH and airbag ECU assembly.
The connectors are properly connected.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the rear seat airbag assembly RH connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the connectors are not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | SST |
| *a | Front view of wire harness connector (to Rear Seat Airbag Assembly RH) |
Connect the connector to the airbag ECU assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the rear seat airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Disconnect SST from connector C.
| Result | Proceed to |
|---|---|
| DTC B003811 is not output | A |
| DTC B003811 is output | B |
A
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>REAR SEAT SIDE AIRBAG ASSEMBLY (for RH Side)>REMOVAL
B
Pre-procedure1
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector (to Rear Seat Airbag Assembly RH) |
Disconnect the Q1 airbag ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(j10)Location & Routingewd_type=routing;type=c;code=j10 Click Connector(j10)Seat>Rear Seat Wire RH>Rear Seat Airbag Assembly RHewd_type=component;type=c;code=j10;pinno=1,2 |
||
| j10-1 - Body ground | Always | 1 MΩ or higher |
| j10-2 - Body ground | Always | 1 MΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the airbag ECU assembly connector.
Connect the rear seat airbag assembly RH connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Post-procedure1None
None
| Result | Proceed to |
|---|---|
| DTC B003811 is not output | A |
| DTC B003811 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B