Home › Suspension › SUSPENSION CONTROL › STABILIZER CONTROL VALVE (for Rear Side) › 2021.04–2021.07
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0473916 STABILIZER CONTROL VALVE(for Rear Side) A

SUSPENSION CONTROL  STABILIZER CONTROL VALVE(for Rear Side)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C459188N01
3.573,0.094 4.49,0.427 0.917,0.333 3.531,0.052 4.531,0.469 1,0.417 1.313,0.021 2.313,0.438 1,0.417 1.354,0.063 2.271,0.396 0.917,0.333 5.167,3.865 5.917,4.031 0.75,0.167 3.24,2.271 3.24,0.188 3.24,0.188 3.573,0.188 true 3.313,2.438 3.313,0.188 true 2.854,2.229 2.854,0.146 2.854,0.146 2.271,0.146 true 3.417,2.25 3.75,2.833 3.75,2.833 4.083,2.833 true 3.917,2.833 3.583,2.25 true 2.75,2.271 2.75,3.104 2.75,3.104 2.583,3.104 true 3.188,4.031 3.188,4.365 3.188,4.365 3.438,4.365 false 4.917,4.281 4.917,3.948 4.917,3.948 5.167,3.948 false 3.635,0.115 4.635,0.365 1,0.25 8 false 44.1 (450, 33) 3.635,0.281 4.635,0.531 1,0.25 8 false 37.8 (385, 28) * 1.417,0.083 2.417,0.333 1,0.25 8 false 15.2 (155, 11) 1.417,0.25 2.417,0.5 1,0.25 8 false 13.4 (137, 10) * 2.396,2.969 2.677,3.323 0.281,0.354 18 false 2 4.406,2.688 4.688,3.042 0.281,0.354 18 false 2 3.781,4.26 4.063,4.615 0.281,0.354 18 false 1 5,4.229 5.333,4.479 0.333,0.25 10 false x 3 5.24,3.885 6.156,4.135 0.917,0.25 8 false 32 (326, 24)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY 48860D (Click here) - -
2 REAR STABILIZER CONTROL TUBE ASSEMBLY - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
* For use with a union nut wrench - -

C459200N01
6.583,0.646 6.802,0.646 false 6.573,0.25 6.865,0.25 false 6.573,1.083 6.823,1.083 false 4,2.667 4,2.917 4,2.917 4.333,2.917 false 6.115,0.135 6.698,0.469 0.583,0.333 18 false 5, 6 6.042,0.521 6.625,0.854 0.583,0.333 18 false 7 - 9 6.396,0.969 6.729,1.302 0.333,0.333 18 false 4 4.396,2.802 4.729,3.135 0.333,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

3 STEP SUB-ASSEMBLY LH - - - -
4 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - - - -
5 BLEED AIR FROM SUSPENSION FLUID - - (Click here) -
6 PRESSURE ACCORDING TO TEMPERATURE MANAGEMENT CHART WHEN FILLING FLUID - - (Click here) -
7 INSPECT FOR SUSPENSION FLUID LEAK - - - (Click here)
8 MEASURE VEHICLE HEIGHT - - - (Click here)
9 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

PROCEDURE

Hide 48860D 1.INSTALL STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY

Z101186

NOTICE:
·

Be careful not to allow any suspension fluid to enter the connector.

·

Do not apply excessive force to the rear stabilizer control tube assembly .




Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

Hide 2.CONNECT REAR STABILIZER CONTROL TUBE ASSEMBLY

a.
C458552C01
3.625,2.469 3.938,2.625 0.313,0.156 10 false *a 5.292,1.344 5.448,1.542 0.156,0.198 10 true A 5.083,0.24 5.24,0.438 0.156,0.198 10 true A 2.354,0.479 2.51,0.677 0.156,0.198 10 true B 0.438,0.073 0.938,0.573 0.5,0.5 18 false i
*a Torque Wrench Fulcrum Length - -


i.

Using a union nut wrench, connect the rear stabilizer control tube assembly.

Torque:
Specified tightening torque (A) : 44.1 N*m (450 kgf*cm, 33 ft.*lbf)
Specified tightening torque (B) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the rear stabilizer control tube assembly.

·

Do not allow any foreign matter such as dirt or dust to enter the rear stabilizer control tube assembly from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

for Specified Tightening Torque (A):

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)):

37.8 N*m (385 kgf*cm, 28 ft.*lbf)

·

for Specified Tightening Torque (B):

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)





Hide 3.INSTALL STEP SUB-ASSEMBLY LH

Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 5.BLEED AIR FROM SUSPENSION FLUID

Z101186

Click here(Click here)

Hide 6.APPLY PRESSURE ACCORDING TO TEMPERATURE MANAGEMENT CHART WHEN FILLING FLUID

Hide 7.INSPECT FOR SUSPENSION FLUID LEAK

Z101186

Click here(Click here)

Hide 8.MEASURE VEHICLE HEIGHT

Z101186

Click here(Click here)

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery , there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART