Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Cannot Proceed to Fingerprint Registration Screen  


DESCRIPTION

If you cannot proceed to the fingerprint registration screen, there may be a malfunction between the certification ECU (smart key ECU assembly) and engine switch and a malfunction in the engine switch, or a dirty sensor.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the engine switch, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Body Electrical > Main Body > Trouble Codes
50001 449
Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTCs are not output A
DTC is output. B



A

2.READ VALUE USING GTS (Fingerprint Authentication Data Fix)

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.READ VALUE USING GTS (Fingerprint Authentication Data Fix)
a.

Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fingerprint Authentication Data Fix Engine switch data status No/Yes No: Data not confirmed
Yes: Data confirmed
-
Body Electrical > Entry&Start > Data List
Tester Display
Fingerprint Authentication Data Fix
50003 440 153

OK:

Fingerprint Authentication Data Fix is "Yes"


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE SWITCH

NG

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH))
3.CHECK ENGINE SWITCH
a.

Check whether the engine switch sensor is dirty.


OK:

Sensor not dirty


Result:
Proceed to
OK
NG



OK

4.CHECK CUSTOMIZATION SETTING

NG

9.WIPE OFF DIRT FROM ENGINE SWITCH
4.CHECK CUSTOMIZATION SETTING
a.

Check the customization setting for the fingerprint authentication function.


Result:
Result Proceed to
Setting is "ON" A
Setting is not "ON" B



A

5.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN

B

7.CHANGE CUSTOMIZATION SETTING
5.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
a.

Check whether you can enter the fingerprint registration screen.


Result:
Result Proceed to
Can enter fingerprint registration screen A
Cannot enter fingerprint registration screen B



A

END

B

6.WHETHER ENGINE STARTS
6.WHETHER ENGINE STARTS
a.
B581613C06
2.583,0.771 2.729,0.573 2.729,0.573 2.865,0.573 true 0.708,0.313 0.854,0.313 0.854,0.313 1.063,0.521 true 0.51,0.229 0.823,0.427 0.313,0.198 10 false *1 2.917,0.5 3.229,0.698 0.313,0.198 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


Check that the engine starts when the engine switch is operated while touching the electrical key transmitter sub-assembly (electrical key) to the surface of the engine switch.


Result:
Result Proceed to
The engine starts A
The engine does not start B



A

END

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHANGE CUSTOMIZATION SETTING
a.

Set the customization setting of the fingerprint authentication function to "ON".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS


Result:
Proceed to
NEXT



NEXT

8.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
8.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
a.

Check whether you can enter the fingerprint registration screen.


Result:
Result Proceed to
Can enter fingerprint registration screen A
Cannot enter fingerprint registration screen B



A

END

B

5.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
9.WIPE OFF DIRT FROM ENGINE SWITCH
a.

Wipe off dirt from the engine switch sensor.

NOTICE:

When cleaning the surface of the sensor, use a soft, dry cloth without any fibers sticking out.



Result:
Proceed to
NEXT



NEXT

10.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
10.CHECK TRANSITION TO FINGERPRINT REGISTRATION SCREEN
a.

Check whether you can enter the fingerprint registration screen.


Result:
Result Proceed to
Can enter fingerprint registration screen A
Cannot enter fingerprint registration screen B



A

END

B

4.CHECK CUSTOMIZATION SETTING
11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH))
a.

Disconnect the I39 connector of the certification ECU (smart key ECU assembly).


b.

Disconnect the I75 connector of the engine switch.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BATTERY)
a.

Connect the I39 connector of the certification ECU (smart key ECU assembly).


b.

Connect the I75 connector of the engine switch.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-10 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR