If you cannot change fingerprint authentication customization, there may be a malfunction between the certification ECU (smart key ECU assembly) and engine switch and a malfunction in the engine switch, or a dirty sensor.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the engine switch, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC is output. | B |
A
B
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fingerprint Authentication Data Fix | Push start switch data status | No/Yes | No: Data not confirmed Yes: Data confirmed |
- |
| Tester Display |
|---|
| Fingerprint Authentication Data Fix |
Fingerprint Authentication Data Fix is "Yes"
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check whether you can enter the fingerprint authentication customize screen.
| Result | Proceed to |
|---|---|
| Can enter fingerprint authentication customize screen | A |
| Cannot enter fingerprint authentication customize screen | B |
A
B
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fingerprint #1 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #2 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #3 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #4 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #5 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #6 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #7 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #8 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #9 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Fingerprint #10 Registration | Fingerprint registration status | without or with | without: Fingerprint not registered with: Fingerprint registered |
- |
| Tester Display |
|---|
| Fingerprint #1 Registration |
| Fingerprint #2 Registration |
| Fingerprint #3 Registration |
| Fingerprint #4 Registration |
| Fingerprint #5 Registration |
| Fingerprint #6 Registration |
| Fingerprint #7 Registration |
| Fingerprint #8 Registration |
| Fingerprint #9 Registration |
| Fingerprint #10 Registration |
"with" is displayed for even 1 fingerprint from No. 1 to No. 10
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I39 connector of the certification ECU (smart key ECU assembly).
Disconnect the I75 connector of the engine switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39,I75)Location & Routingewd_type=routing;type=c,c;code=I39,I75 |
||
| I39-8 (LIN) - I75-4 (LIN) | Always | Below 1 Ω |
| I39-8 (LIN) or I75-4 (LIN) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the I39 connector of the certification ECU (smart key ECU assembly).
Connect the I75 connector of the engine switch.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I75)Location & Routingewd_type=routing;type=c;code=I75 |
||
| I75-10 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I75)Location & Routingewd_type=routing;type=c;code=I75 |
||
| I75-3 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG