| *A | w/ Condenser Fan | - | - |
| *1 | RADIATOR ASSEMBLY | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
| *A | w/o Condenser Fan | *B | w/ Condenser Fan |
| *1 | ENGINE ROOM MAIN WIRE | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *1 | FLUID COUPLING ASSEMBLY WITH FAN | *2 | FAN PULLEY |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *1 | ENGINE SIDE COVER SUB-ASSEMBLY LH | *2 | ENGINE SIDE COVER SUB-ASSEMBLY RH |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
16561 1.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
16681 2.INSTALL UPPER RADIATOR AIR GUIDE PLATE
4.INSTALL COOLER BRACKET
88590 6.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
7.INSTALL RADIATOR WITH COOLER CONDENSER ASSEMBLY
w/ Condenser Fan
Install the radiator with cooler condenser assembly to the vehicle.
Perform the following procedure with 2 or more people to prevent damage to the radiator with cooler condenser assembly.
When removing the radiator with cooler condenser assembly from the vehicle, do not apply excessive force to the cooler pipe or cooling hoses.
Set the radiator bracket hooks into the radiator support holes.
Install the radiator with cooler condenser assembly with the 6 bolts.
Attach the clamp and connect the connector.
w/o Condenser Fan
Install the radiator with cooler condenser assembly to the vehicle.
Perform the following procedure with 2 or more people to prevent damage to the radiator with cooler condenser assembly.
When removing the radiator with cooler condenser assembly from the vehicle, do not apply excessive force to the cooler pipe or cooling hoses.
Set the radiator bracket hooks into the radiator support holes.
Install the radiator with cooler condenser assembly with the 6 bolts.
88711 8.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and connecting part of the cooler condenser assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose.
ND-OIL 8 or equivalent
Install a new O-ring to the No. 1 cooler refrigerant discharge hose.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
88710E 9.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the air conditioning tube and accessory assembly and connecting part of the No. 2 air conditioning tube and accessory assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.
ND-OIL 8 or equivalent
Install a new O-ring to the air conditioning tube and accessory assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the air conditioning tube and accessory assembly to the No. 2 air conditioning tube and accessory assembly with the bolt.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
44402 10.CONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY
16691A 11.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH
16695A 12.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16583 13.INSTALL NO. 2 RADIATOR BRACKET
Hook the claw of the No. 2 radiator bracket as shown in the illustration.
Install the No. 2 radiator bracket with the 4 bolts.
16695A 14.CONNECT FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16296 15.CONNECT NO. 8 WATER BY-PASS HOSE
16297 16.CONNECT NO. 9 WATER BY-PASS HOSE
16582 17.INSTALL NO. 1 RADIATOR BRACKET
Hook the claw of the No. 1 radiator bracket as shown in the illustration.
Install the No. 1 radiator bracket with the 4 bolts.
16035B 18.CONNECT FRONT WATER BY-PASS JOINT SUB-ASSEMBLY
16035 19.CONNECT WATER HOSE JOINT
16268 20.CONNECT NO. 1 WATER BY-PASS PIPE
161B0 21.CONNECT ELECTRIC WATER PUMP ASSEMBLY
82H21F 22.INSTALL CONNECTOR COVER
16561C 23.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
16550B 24.INSTALL NO. 2 INTERCOOLER COOLING RADIATOR ASSEMBLY
16711 25.INSTALL FAN SHROUD
Install the fan pulley to the fan bracket sub-assembly.
Place the fan shroud together with the fluid coupling assembly with fan between the radiator and engine.
Be careful not to damage the radiator core.
Temporarily install the fluid coupling assembly with fan to the fan bracket sub-assembly with the 4 nuts. Tighten the 4 nuts as much as possible by hand.
Align the paint marks on the head of the fan bracket sub-assembly stud bolt with the paint marks of the same color on the outer edge of the fluid coupling flange and set the fluid coupling to the fan bracket sub-assembly.
Attach the claws of the fan shroud to the radiator as shown in the illustration.
Install the fan shroud with the 2 bolts.
Tighten the 4 nuts of the fluid coupling assembly with fan.
26.CONNECT OIL COOLER TUBE SUB-ASSEMBLY
| *a | Paint Mark | *b | Stopper |
| *c | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) | *d | 2.0 to 7.0 mm (0.0787 to 0.276 in.) |
| *e | 60° | - | - |
Connect the oil cooler tube sub-assembly to the fan shroud with the 2 bolts.
Tightening order: Temporarily install bolt A → Tighten bolt B → Tighten bolt A
Connect the oil cooler tube sub-assembly to the radiator assembly and slide the hose clip to secure it as shown in the illustration.
Make sure the oil cooler tube sub-assembly is securely inserted to the stopper.
16278 27.CONNECT NO. 2 WATER BY-PASS PIPE
16572D 28.INSTALL NO. 2 RADIATOR HOSE
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 7.0 mm (0.0787 to 0.276 in.) | *d | 30° |
| *e | Upper Side | *f | RH Side |
Attach the clamp.
Install the No. 2 radiator hose to the water inlet and radiator assembly and slide the 2 hose clips to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the No. 2 radiator hose is securely inserted to the stopper.
16571C 29.INSTALL NO. 1 RADIATOR HOSE
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 7.0 mm (0.0787 to 0.276 in.) | *d | 30° |
| *e | Upper Side | *f | Rear Side |
| *g | RH Side | - | - |
Install the No. 1 radiator hose to the water outlet pipe and radiator assembly and slide the 2 hose clips to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the No. 1 radiator hose is securely inserted to the stopper.
16264D 30.INSTALL NO. 2 WATER BY-PASS HOSE
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 5.0 mm (0.0787 to 0.197 in.) | *d | 25° |
| *e | 45° | *f | Rear Side |
| *g | LH Side | - | - |
Connect the No. 2 water by-pass hose to the water inlet and slide the hose clip to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the No. 2 water by-pass hose is securely inserted to the stopper.
164A2 31.INSTALL RADIATOR RESERVE TANK ASSEMBLY
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 5.0 mm (0.0787 to 0.197 in.) | *d | 25° |
| *e | 30° | *f | Rear Side |
| *g | Upper Side | *h | RH Side |
|
Bolt A |
|
Bolt B |
Connect the radiator reserve tank assembly to the No. 2 water by-pass hose and slide the hose clip to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the No. 2 water by-pass hose is securely inserted to the stopper.
Install the radiator reserve tank assembly to the radiator assembly with the 3 bolts.
Connect the No. 1 water by-pass hose to the radiator assembly and slide the hose clip to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the No. 1 water by-pass hose is securely inserted to the stopper.
16267 32.CONNECT NO. 3 WATER BY-PASS HOSE
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 6.0 mm (0.0787 to 0.236 in.) | *d | 60° |
| *e | Upper Side | - | - |
Attach the 2 clamps.
Connect the No. 3 water by-pass hose to the No. 1 intercooler cooling water pipe and slide the hose clip to secure it as shown in the illustration.
Make sure the No. 3 water by-pass hose is securely inserted to the stopper.
16261 33.CONNECT WATER BY-PASS HOSE
| *a | Paint Mark | *b | Stopper |
| *c | 2.0 to 5.0 mm (0.0787 to 0.1969 in.) | *d | 60° |
| *e | Upper Side | *f | RH Side |
Connect the water by-pass hose to the radiator reserve tank assembly and slide the hose clip to secure it as shown in the illustration.
Install so that the paint mark and positioning stopper are securely overlapped.
Make sure the water by-pass hose is securely inserted to the stopper.
16361A 34.INSTALL FAN AND GENERATOR V BELT
35.INSTALL FRONT BUMPER ASSEMBLY
for Standard
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>INSTALLATION
for Aero Type
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Aero Type)>INSTALLATION
36.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
37.ADD ENGINE COOLANT
38.ADD COOLANT (for Intercooler)
39.WARM UP ENGINE
40.INSPECT FOR REFRIGERANT LEAK
41.INSPECT FOR COOLANT LEAK
42.INSPECT FOR COOLANT LEAK (for Intercooler)
51410 43.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
53292A 44.INSTALL UPPER RADIATOR SUPPORT SEAL
12601B 45.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY