| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | COOLER CONDENSER ASSEMBLY | 884A0 | ( ) |
- | - |
| 2 | COOLER BRACKET | - | - | - | - |
| 3 | NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY | 88710G | ( ) |
- | - |
| *A | for 1GR-FE | *B | for V35A-FTS, F33A-FTV |
| *C | for Type A | *D | for Type B |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | BLOWER ASSEMBLY WITH SHROUD | 88590 | |||
| 5 | RADIATOR WITH COOLER CONDENSER ASSEMBLY | - | - | - | - |
| *A | for 1GR-FE | *B | for V35A-FTS, F33A-FTV |
| *C | w/ Condenser Fan | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
884A0 1.INSTALL COOLER CONDENSER ASSEMBLY
| *A | for 1GR-FE | *B | for V35A-FTS, F33A-FTV |
| *C | for Type A | *D | for Type B |
Install the cooler condenser assembly with the 2 bolts and 2 nuts.
Do not damage the cooler condenser assembly and radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the condenser as follows.
Add 40 cc (1.35 fl. oz)
ND-OIL 8 or equivalent
2.INSTALL COOLER BRACKET
88710G 3.INSTALL NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
| *A | for Type A | *B | for Type B |
Install the No. 2 air conditioning and tube accessory assembly using the following procedure.
1. Remove the vinyl tape from the No. 2 air conditioning tube and accessory assembly and connecting part of the cooler condenser assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 2 air conditioning tube and accessory assembly.
ND-OIL 8 or equivalent
2. Install the O-ring to the No. 2 air conditioning and tube accessory assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
3. Connect the No. 2 air conditioning and tube accessory assembly to the cooler condenser assembly with the 2 bolts.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
88590 4.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (COOLING)>RADIATOR>INSTALLATION
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (COOLING)>RADIATOR>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (COOLING)>RADIATOR>INSTALLATION
5.INSTALL RADIATOR WITH COOLER CONDENSER ASSEMBLY
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (COOLING)>RADIATOR>INSTALLATION
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (COOLING)>RADIATOR>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (COOLING)>RADIATOR>INSTALLATION