Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0467301 TRANSMISSION WIRE A

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456960N01
5.021,2.031 5.688,2.031 false 2.917,3 3.25,3 false 2.583,1.677 2.917,1.677 false 0.948,2.094 1.135,2.094 1.135,2.094 1.771,1.823 false 5.052,1.625 5.719,1.625 false 1.677,2.448 1.865,2.448 1.865,2.448 2.5,2.177 false 6,1.885 6.281,2.24 0.281,0.354 18 false 4 0.771,1.927 1.052,2.281 0.281,0.354 18 false 3 2.969,1.49 3.25,1.844 0.281,0.354 18 false 2 2.615,2.052 3.073,2.25 0.458,0.198 10 false x 3 2.615,2.292 3.073,2.49 0.458,0.198 10 false x 3 3.302,2.813 3.583,3.167 0.281,0.354 18 false 1 5.771,1.531 5.927,1.729 0.156,0.198 10 false ● 1.51,2.354 1.823,2.552 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TRANSMISSION VALVE BODY ASSEMBLY 35400A - - -
2 TRANSMISSION REVOLUTION SENSOR (SP2) 89413V - - -
3 TRANSMISSION REVOLUTION SENSOR (NT) 89413N - - -
4 TRANSMISSION WIRE 82125J (Click here) - -

*1 TRANSMISSION WIRE CLAMP - -
● Non-reusable part - -

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. for V35A-FTS:(Click here)
for F33A-FTV:(Click here)

PROCEDURE

Hide 35400A 1.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

Hide 89413V 2.REMOVE TRANSMISSION REVOLUTION SENSOR (SP2)

Hide 89413N 3.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)

Hide 82125J 4.REMOVE TRANSMISSION WIRE

a.
C456928C01
0.271,0.063 0.552,0.417 0.281,0.354 18 true i 4.427,0.021 4.698,0.313 0.271,0.292 18 true ii 0.604,1.99 1.188,2.344 0.583,0.354 18 true iii, iv 4.167,2.01 4.75,2.365 0.583,0.354 18 true v
V113147

Turn
V113148

Pull Down the Lever


i.

Remove the 3 bolts and 3 transmission wire clamps.


ii.

Using a 10 mm union nut wrench, remove the bolt as shown in the illustration.


iii.

Disconnect the transmission wire connector.

HINT:

Disengage the claw, pull down the lever, and then disconnect the transmission wire connector.



iv.

Pull out the transmission wire from the automatic transmission assembly.


v.

Remove the O-ring from the transmission wire.