Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2021.07
RM38G0E _57 Power Source / Network _100627 POWER DISTRIBUTION _0467797 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B613002C03
3,2.729 6.771,4.813 3.771,2.083 6.542,0.198 6.802,0.198 false 6.552,0.594 6.792,0.594 false 1.75,2 2.25,2 2.25,2 2.802,2.469 false 1.719,1.063 2.417,1.063 false 1.75,3.667 2.083,3.667 false 4.438,2.833 4.021,2.833 false 3.25,4.25 3.083,4.25 3.083,4.25 3.083,4.417 false 4.854,4.542 5.188,4.542 false 5.74,3.844 6.031,3.844 false 4.417,1.729 4.417,2.063 4.417,2.063 4.583,2.063 false 5.635,1.396 5.635,1.646 5.635,1.646 5.781,1.646 false 6.365,0.073 6.542,0.333 0.177,0.26 18 false 1 6.365,0.458 7.042,0.938 0.677,0.479 18 false 2 5.833,1.5 6.115,1.854 0.281,0.354 18 false 4 4.771,0.563 5.083,0.76 0.313,0.198 10 false x 4 1.573,1.833 1.729,2.104 0.156,0.271 18 false 3 1.552,0.917 1.833,1.271 0.281,0.354 18 false 5 2.302,3.583 2.583,3.938 0.281,0.354 18 false 6 3.885,2.729 4.167,3.083 0.281,0.354 18 false 8 3.042,4.427 3.323,4.781 0.281,0.354 18 false 9 5.25,4.396 5.531,4.75 0.281,0.354 18 false 7 6.323,3.74 6.479,3.938 0.156,0.198 10 false ● 2.01,3.042 2.469,3.24 0.458,0.198 10 false x 2 6.417,3.729 7,4.083 0.583,0.354 18 false 10 4.615,1.948 4.896,2.302 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - (Click here) - -
3 LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 73990 - - -
4 INSTRUMENT PANEL BOX DOOR COVER 55443A (Click here) - -
5 LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY 55320 - - -
6 ECU INTEGRATION BOX RH 82877 (Click here) - -
7 POWER DISTRIBUTION BOX ASSEMBLY 82730G - - -
8 JUNCTION BLOCK BRACKET 82673A - - -
9 JUNCTION BLOCK BRACKET 82673B - - -
10 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -

*A w/ Door Control Battery - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Main body ECU (multiplex network body ECU) ECU configuration - (Click here)
Perform code registration
·

Wireless door lock control system

·

Entry and start system

·

Engine start


See Service Bulletin for the registration method.

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

Do not remove the main body ECU (multiplex network body ECU) except when replacing it.

·

When removing the main body ECU (multiplex network body ECU), always replace it with a new one.




Hide 2. DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)

a.
Z101186

NOTICE:
·

Always ensure that the cable is disconnected from the negative (-) battery terminal and the door control battery is fully discharged when removing or installing the power distribution box assembly.

·

Make sure to perform the following procedure before removal and installation of the power distribution box assembly.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

(Click here)



HINT:
·

When the ignition switch is turned off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.

·

Approximately 90 seconds after the ignition switch is turned on (IG), the door control battery becomes fully charged.

·

When approximately 30 minutes or more have elapsed after the ignition switch is turned off, the Active Test may not be able to be performed.




i.

Turn the ignition switch off.

Body Electrical > Main Body > Active Test
Tester Display Control Range
Collision Door Lock Release OFF/ON
NOTICE:

Do not perform the Active Test at this time.



ii.

Disconnect the cable from the negative (-) battery terminal.

for 1GR-FE:

Click hereGeneral>MAINTENANCE>1GR-FE BATTERY>REMOVAL

for V35A-FTS:

Click hereGeneral>MAINTENANCE>V35A-FTS BATTERY>REMOVAL

for F33A-FTV:

Click hereGeneral>MAINTENANCE>F33A-FTV BATTERY>REMOVAL


iii.

Perform the "Shock Detection Unlock" Active Test repeatedly until the multiplex network body ECU (main body ECU) communication lost error message "Lost communication with vehicle" is displayed on the GTS.

Body Electrical > Main Body > Active Test
Tester Display
Collision Door Lock Release
50004 449 13
HINT:
·

When the cable is disconnected from the negative (-) battery terminal and the door control battery becomes completely discharged, the multiplex network body ECU (main body ECU) communication lost message "Lost communication with vehicle" is displayed on the GTS.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.





Hide 73990 3.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55443A 4.REMOVE INSTRUMENT PANEL BOX DOOR COVER

Z101186

Click here(Click here)

Hide 55320 5.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 82877 6.REMOVE ECU INTEGRATION BOX RH

a.
E463744C01
0.563,2.844 0.969,3.188 0.406,0.344 18 true iii 0.531,0.375 0.938,0.719 0.406,0.344 18 true ii 4.479,0.406 4.688,0.729 0.208,0.323 18 true i 4.01,2.823 4.417,3.167 0.406,0.344 18 true iv
V113147

Remove in this Direction
V100135

Connector
V100136

Nut
V100137

Bolt


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


ii.

Disconnect the 9 connectors and detach the clamp.


iii.

w/ Stop and Start System:

1.

Disconnect the 3 connectors.



iv.

Remove the 2 nuts and bolt.



b.
E463745C01
1.021,0.24 1.302,0.594 0.281,0.354 18 true i 3.74,0.188 4.021,0.542 0.281,0.354 18 true ii
V113147

Remove in this Direction - -


i.

Detach the clamp and disconnect the connector.


ii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw, disconnect the 2 lever connectors and remove the ECU integration box RH.



Hide 82730G 7.REMOVE POWER DISTRIBUTION BOX ASSEMBLY

a.
E463855C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 82673A 8.REMOVE JUNCTION BLOCK BRACKET

a.
E463859


Hide 82673B 9.REMOVE JUNCTION BLOCK BRACKET

a.
E463860


Hide 89221 10.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E463856C01
1.031,1.344 1.281,1.344 false 0.854,1.198 0.656,1.198 0.656,1.198 0.656,1.427 true 2.75,3.427 2.979,3.427 2.979,3.427 3.271,2.948 false 1.302,1.25 1.615,1.448 0.313,0.198 10 false *1 0.594,1.469 0.906,1.667 0.313,0.198 10 false *2 2.573,3.333 2.885,3.531 0.313,0.198 10 false *a 1.656,0.24 1.938,0.594 0.281,0.354 18 false i 6.833,1.438 7.115,1.792 0.281,0.354 18 false ii 5.823,0.167 6.104,0.521 0.281,0.354 18 false iii 2.563,2.177 2.844,2.531 0.281,0.354 18 false iv
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a Rib - -
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V100135

Push in this Direction
V100136

Horizontally Insert a Thin-bladed Screwdriver


i.

Press the claw of the power distribution box assembly as shown in the illustration and release the lock of the main body ECU (multiplex network body ECU).


ii.

With the lock released, insert a screwdriver with its tip wrapped with protective tape horizontally in between the main body ECU (multiplex network body ECU) and the power distribution box assembly.

NOTICE:

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).



iii.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:
·

Do not pry and lift with the screwdriver.

·

Replace the power distribution box assembly or the main body ECU (multiplex network body ECU) when the connector terminal, locking section or case is damaged or deformed.




iv.

Lift up the rib of the main body ECU (multiplex network body ECU) and slide the main body ECU (multiplex network body ECU) to remove it as shown in the illustration.

NOTICE:

Do not touch the ECU connector terminal with your fingers.