Home › Power Source / Network › POWER DISTRIBUTION › INTEGRATION RELAY › from 2021.07
RM38G0E _57 Power Source / Network _100627 POWER DISTRIBUTION _0468585 INTEGRATION RELAY A

POWER DISTRIBUTION  INTEGRATION RELAY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E465044N01
6.552,0.198 6.875,0.198 false 6.573,0.656 6.823,0.656 false 0.573,0.854 0.917,0.854 false 1.438,1.375 1.781,1.375 false 6.354,0.052 6.635,0.406 0.281,0.354 18 false 1 6.375,0.49 6.656,0.844 0.281,0.354 18 false 2 2.052,1.229 2.333,1.583 0.281,0.354 18 false 4 0.375,0.708 0.656,1.063 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 NO. 1 RELAY BLOCK COVER 82661 - - -
4 SEMICONDUCTOR POWER INTEGRATION ECU 82644 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the semiconductor power integration ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 82661 3.REMOVE NO. 1 RELAY BLOCK COVER

a.
E465158C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 82644 4.REMOVE SEMICONDUCTOR POWER INTEGRATION ECU

a.
E465159C01
0.115,0.021 0.396,0.375 0.281,0.354 18 false i 6.188,1.115 6.396,1.479 0.208,0.365 18 true ii 3.979,0.063 4.26,0.417 0.281,0.354 18 false iii
V113147

Remove in this Direction - -


i.

Detach the claw and pull up the semiconductor power integration ECU.


ii.

Disconnect the connector.


iii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw, disconnect the lever connector and remove the semiconductor power integration ECU.