Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ELECTRICAL KEY OSCILLATOR (for Outside Luggage Compartment) › from 2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467831 ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment) A

THEFT DETERRENT / KEYLESS ENTRY  ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E462544N06
3.865,2.063 4.094,1.844 4.094,1.844 4.323,1.844 false 5.667,2 5.875,1.833 5.875,1.833 6.083,1.833 false 6.469,0.323 6.771,0.323 false 6.115,1.698 6.396,2.052 0.281,0.354 18 false 2 4.375,1.698 4.656,2.052 0.281,0.354 18 false 3 5.938,0.177 6.104,0.51 0.167,0.333 18 false 1 6.115,0.208 6.813,0.49 0.698,0.281 12 false (*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR BUMPER ASSEMBLY - - - -
3 ELECTRICAL KEY ANTENNA 89997 - - -

*A w/ Hands Free Power Back Door - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the electrical key antenna removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
w/ Hands Free Power Back Door:

Disconnect cable from negative (-) battery terminal


Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Rear bumper assembly (Including removal and installation)
w/ Parking Support Brake System:
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT

·

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.



PROCEDURE

Hide 1. PRECAUTION (w/ Hands Free Power Back Door)

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 89997 3.REMOVE ELECTRICAL KEY ANTENNA

a.
E462545