Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER (for Standard) › from 2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468071 REAR BUMPER(for Standard) A

EXTERIOR PANELS / TRIM  REAR BUMPER(for Standard)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B610841N01
3.917,4.417 6.26,5.552 2.344,1.135 0.292,0.063 3.708,2 3.417,1.938 1.052,2.875 1.052,2.625 1.052,2.625 1.552,2.625 false 2.073,4.667 2.073,4.333 2.073,4.333 2.24,4.333 false 3.615,3.417 3.615,2.75 3.615,2.75 3.948,2.75 false 3.083,2.219 3.417,2.219 false 4.76,1.813 5.01,1.813 false 6.146,1.875 6.146,1.625 6.146,1.625 6.313,1.625 false 5.719,4.083 6.219,4.083 false 4.458,5.083 4.458,5.25 4.458,5.25 4.792,5.25 false 5.604,5.26 5.854,5.26 false 6.563,0.281 6.813,0.281 false 6.594,0.677 6.76,0.677 false 3.146,1.771 1.979,1.771 1.979,1.771 1.979,1.604 false 2.469,1.76 2.469,1.51 false 2.104,1.167 2.354,0.917 2.354,0.917 2.635,0.906 false 1.26,1.417 1.51,1.417 1.51,1.417 1.76,1.167 true 1.5,0.469 1.5,0.219 1.5,0.219 2,0.219 false 1.802,2.49 2.083,2.844 0.281,0.354 18 false 3 3.646,2.083 3.927,2.438 0.281,0.354 18 false 7 5.26,1.656 5.542,2.01 0.281,0.354 18 false 8 6.094,0.156 6.375,0.51 0.281,0.354 18 false 1 6.115,0.552 6.396,0.906 0.281,0.354 18 false 2 6.573,1.49 6.854,1.844 0.281,0.354 18 false 4 2.479,4.219 2.76,4.573 0.281,0.354 18 false 5 5.51,3.979 5.792,4.333 0.281,0.354 18 false 6 6.083,5.104 6.365,5.458 0.281,0.354 18 false 9 4.99,5.135 5.375,5.479 0.385,0.344 18 false 10 4.156,2.615 4.542,2.958 0.385,0.344 18 false 14 1.979,3.156 2.438,3.354 0.458,0.198 10 false x 2 2.271,5.229 2.729,5.427 0.458,0.198 10 false x 2 3.729,4.24 4.188,4.438 0.458,0.198 10 false x 2 2.927,4.167 3.385,4.365 0.458,0.198 10 false x 6 5.302,2.75 5.76,2.948 0.458,0.198 10 false x 2 6.5,4.458 6.958,4.656 0.458,0.198 10 false x 2 5.333,3.271 5.792,3.469 0.458,0.198 10 false x 5 4.031,4.5 4.406,4.74 0.375,0.24 12 false *B 6.26,0.188 6.635,0.427 0.375,0.24 12 false (*A) 6.281,0.583 6.656,0.823 0.375,0.24 12 false (*A) 1.073,1.344 1.531,1.542 0.458,0.198 10 false *1 2.083,0.083 2.469,0.427 0.385,0.344 18 false 11 2.667,0.771 3.052,1.115 0.385,0.344 18 false 13 3.25,1.604 3.635,1.948 0.385,0.344 18 false 12 0.406,0.115 0.781,0.354 0.375,0.24 12 false *C 2.99,1.25 3.448,1.448 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH 75606B (Click here) - -
4 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH 75605B (Click here) - -
5 QUARTER PANEL REAR MUDGUARD LH 76626E (Click here) - -
6 QUARTER PANEL REAR MUDGUARD RH 76625G (Click here) - -
7 REAR COMBINATION LIGHT COVER LH 81498 (Click here) - -
8 REAR COMBINATION LIGHT COVER RH 81497 (Click here) - -
9 REAR BUMPER PLATE RH 52163A (Click here) - -
10 REAR BUMPER NO. 1 PLATE 52162B (Click here) - -
11 SPARE TIRE - - - -
12 EYELET PINTLE HOOK 51985A - - -
13 PINTLE HOOK ASSEMBLY 51980A - - -
14 REAR BUMPER ASSEMBLY - (Click here) - -

*A w/ Hands Free Power Back Door *B for Step
*C w/ Pintle Hook - -
*1 PINTLE HOOK BRACKET - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear bumper assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
w/ Hands Free Power Back Door:

Disconnect cable from negative (-) battery terminal


Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT

·

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.

·

When the rear bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform ultrasonic sensor detection angle measurement.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION



PROCEDURE

Hide 1. PRECAUTION (w/ Hands Free Power Back Door)

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Hands Free Power Back Door)

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.







Hide 75606B 3.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH

Z101186

Click here(Click here)

Hide 75605B 4.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH

a.

Use the same procedure described for the LH side.


Hide 76626E 5.REMOVE QUARTER PANEL REAR MUDGUARD LH

Z101186

Click here(Click here)

Hide 76625G 6.REMOVE QUARTER PANEL REAR MUDGUARD RH

a.

Use the same procedure described for the LH side.


Hide 81498 7.REMOVE REAR COMBINATION LIGHT COVER LH

a.
B610760C01
2.552,0.75 2.833,1.104 0.281,0.354 18 false i 4.354,0.458 4.635,0.813 0.281,0.354 18 false ii 1,2.479 1.281,2.833 0.281,0.354 18 false iii
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3) - -


i.

Put protective tape around the rear combination light cover LH.


ii.

Detach the claw as shown in the illustration.


iii.

Detach the claw and remove the rear combination light cover LH as shown in the illustration.



Hide 81497 8.REMOVE REAR COMBINATION LIGHT COVER RH

a.

Use the same procedure described for the LH side.


Hide 52163A 9.REMOVE REAR BUMPER PLATE RH (for Step)

a.
B610759C01
2.625,0.531 2.906,0.885 0.281,0.354 18 false i 3.635,0.115 3.917,0.469 0.281,0.354 18 true ii 0.469,2.021 0.75,2.375 0.281,0.354 18 true iii
V113146

Place Hand Here
V113147

Remove in this Direction


i.

Put protective tape around the rear bumper plate RH.


ii.

Place your hand at the positions shown in the illustration and detach the claw as shown in the illustration.


iii.

Place your hand at the positions shown in the illustration and detach the claw and remove the rear bumper plate RH as shown in the illustration.



Hide 52162B 10.REMOVE REAR BUMPER NO. 1 PLATE (for Step)

a.
B610761C01
1.25,0.26 1.531,0.615 0.281,0.354 18 false i 4.094,0.177 4.375,0.531 0.281,0.354 18 true ii 0.438,3.052 0.719,3.406 0.281,0.354 18 true iii 4.104,3.083 4.385,3.438 0.281,0.354 18 true iv 6.917,0.521 7.073,0.719 0.156,0.198 10 true 1 6.635,0.26 6.792,0.458 0.156,0.198 10 true 2 6.729,0.781 6.885,0.979 0.156,0.198 10 true 3 6.552,0.833 6.708,1.031 0.156,0.198 10 true 4 6.344,0.375 6.5,0.573 0.156,0.198 10 true 5 6.313,0.896 6.469,1.094 0.156,0.198 10 true 6 6.104,0.969 6.26,1.167 0.156,0.198 10 true 7 5.938,0.51 6.094,0.708 0.156,0.198 10 true 8 5.865,1.042 6.021,1.24 0.156,0.198 10 true 9 5.667,0.552 5.823,0.75 0.156,0.198 10 true 10 5.646,1.094 5.802,1.292 0.156,0.198 10 true 11 5.125,0.667 5.281,0.865 0.156,0.198 10 true 13 5.323,1.188 5.479,1.385 0.156,0.198 10 true 12 5.042,1.24 5.198,1.438 0.156,0.198 10 true 14 4.656,1.281 4.813,1.479 0.156,0.198 10 true 15 4.292,1 4.448,1.198 0.156,0.198 10 true 16 2.51,3.76 2.677,3.958 0.167,0.198 10 true 4 3.104,3.417 3.26,3.615 0.156,0.198 10 true 1 2.906,3.635 3.063,3.833 0.156,0.198 10 true 2 2.698,3.688 2.854,3.885 0.156,0.198 10 true 3 2.302,3.813 2.458,4.01 0.156,0.198 10 true 5 2.083,3.885 2.24,4.083 0.156,0.198 10 true 6 1.833,3.958 1.99,4.156 0.156,0.198 10 true 7 1.563,4.031 1.719,4.229 0.156,0.198 10 true 8 1.26,4.083 1.417,4.281 0.156,0.198 10 true 9 0.906,4.125 1.063,4.323 0.156,0.198 10 true 10
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


i.

Put protective tape around the rear bumper No. 1 plate.


ii.

Place your hand at the positions shown in the illustration and detach the claw and guide in the order shown in the illustration.


iii.

Detach the claw in the order shown in the illustration.


iv.

Detach the claw and remove the rear bumper No. 1 plate as shown in the illustration.



Hide 11.REMOVE SPARE TIRE (w/ Pintle Hook)

a.
B610828


Hide 51985A 12.REMOVE EYELET PINTLE HOOK (w/ Pintle Hook)

a.
B610829


Hide 51980A 13.REMOVE PINTLE HOOK ASSEMBLY (w/ Pintle Hook)

a.
B610830


Hide 14.REMOVE REAR BUMPER ASSEMBLY

a.
B610762N01
2.521,0.198 2.802,0.552 0.281,0.354 18 false i 4.135,0.052 4.417,0.406 0.281,0.354 18 true ii

i.

Put protective tape around the rear bumper assembly.


ii.

Remove the clip.



b.

Use the same procedure for the other side.


c.
B663299C02
0.417,0.052 0.698,0.406 0.281,0.354 18 false i 3.76,0.042 4.042,0.396 0.281,0.354 18 false ii 3.333,1.906 3.615,2.26 0.281,0.354 18 false iii 3.333,2.188 3.573,2.438 0.24,0.25 12 true *A
*A w/ TOYOTA Parking Assist-sensor System - -
V100135

Bolt
V100136

Screw
V100137

Connector - -


i.

Remove the 2 bolts and 6 screws.


ii.

Remove the 5 bolts and 2 screws.


iii.

w/ TOYOTA Parking Assist-sensor System:

1. Disconnect the connector.



d.
B610766C01
0.302,0.073 0.583,0.427 0.281,0.354 18 false i 4.063,0.115 4.344,0.469 0.281,0.354 18 true ii 2.083,2.219 2.365,2.573 0.281,0.354 18 true iii
V113147

Remove in this Direction - -


i.

Detach the claw as shown in the illustration.


ii.

Detach the claw as shown in the illustration.


iii.

Detach the clip and guide and remove the rear bumper assembly as shown in the illustration.