Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467873 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B608599N01
5.958,2.01 6.292,2.01 true 1.219,3.042 1.552,3.042 true 6.458,0.656 6.792,0.656 true 6.5,0.24 6.833,0.24 true 3.792,2.74 3.792,3.052 true 3.729,3.031 4.01,3.385 0.281,0.354 18 false 5 1.042,2.885 1.323,3.24 0.281,0.354 18 false 4 6.583,1.854 6.865,2.208 0.281,0.354 18 false 3 6.354,0.073 6.635,0.427 0.281,0.354 18 false 1 6.313,0.479 6.594,0.833 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - (Click here) - -
3 LOWER NO. 2 STEERING WHEEL COVER - (Click here) - -
4 LOWER NO. 3 STEERING WHEEL COVER - (Click here) - -
5 HORN BUTTON ASSEMBLY 45130 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 3.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B612630N01
4.167,0.042 4.448,0.396 0.281,0.354 18 false ii 0.615,0.042 0.896,0.396 0.281,0.354 18 false i

i.

Apply protective tape as shown in the illustration.


ii.

Insert a screwdriver with its tip wrapped with protective tape into the cutout of the lower No. 2 steering wheel cover and disengage the claw and guide to remove the lower No. 2 steering wheel cover.



Hide 4.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B612631N01
4.167,0.042 4.448,0.396 0.281,0.354 18 false ii 0.667,0.042 0.948,0.396 0.281,0.354 18 false i

i.

Apply protective tape as shown in the illustration.


ii.

Insert a screwdriver with its tip wrapped with protective tape into the cutout of the lower No. 3 steering wheel cover and disengage the claw and guide to remove the lower No. 3 steering wheel cover.



Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY

Z101186

CAUTION:
·
B528833N02
1.01,1.594 0.583,1.594 false 0.406,1.51 0.719,1.708 0.313,0.198 10 false *a

When storing the horn button assembly, keep the airbag deployment side (*a) facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.




a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B608602C01
0.635,0.177 0.906,0.521 0.271,0.344 18 false i 5.271,1.698 5.552,2.083 0.281,0.385 18 false iii 6.188,1.99 6.448,2.333 0.26,0.344 18 false ii 6.156,1.365 6.438,1.75 0.281,0.385 18 false v 6.531,1.708 6.813,2.094 0.281,0.385 18 false iv
V113147

Release in this Direction - -


i.

Using a screwdriver with its tip wrapped with protective tape, push in the torsion springs to disengage the pins as shown in the illustration.

NOTICE:

Do not drop the horn button assembly.



ii.

Tilt the horn button assembly toward the seat and support it with one hand.

NOTICE:

When disconnecting the horn button assembly, do not pull the airbag wire harness.



iii.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iv.

Disconnect the horn connector.


v.

Disengage the clamp and remove the horn button assembly.