Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
1. PRECAUTION
An airbag or pretensioner may be accidentally deployed by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.
Never dispose of a rear seat airbag assembly with an undeployed airbag.
The airbag produces an exploding sound when it is deployed, so perform the operation outdoors where it will not disturb nearby residents.
When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.
When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the rear seat airbag assembly RH.
The rear seat airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat airbag assembly RH with a deployed airbag.
Do not apply water, etc. to a rear seat airbag assembly RH with a deployed airbag.
Always wash your hands with water after completing the operation.
When scrapping a vehicle equipped with an SRS or disposing of the rear seat airbag assembly RH, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.
2.DISPOSE OF REAR SEAT AIRBAG ASSEMBLY RH (When Installed to Vehicle)
When disposing of a rear seat airbag assembly RH, never use the customer's vehicle to deploy the airbag.
Be sure to perform the following procedure when deploying the airbag.
Prepare a battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Disconnect the cable from the negative (-) battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
for 1GR-FE:
for V35A-FTS:
for F33A-FTV:
Remove the rear seat No. 1 cushion hinge cover.
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>REMOVAL
Remove the rear seat No. 3 cushion hinge cover.
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>REMOVAL
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Install SST.
Connect SST to the rear seat airbag assembly RH.
Pass SST through the gap shown in the illustration.
Operate the rear No. 1 seat assembly RH to its sitting position.
Check that there is no looseness in the rear seat airbag assembly RH.
Connect SST together (09082-00700 and 09082-00820).
To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.
| *a | Battery |
| *b | 10 m (32.8 ft.) or more |
Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.
Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Take care not to damage the SST wire harness.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press the SST activation switch to deploy the airbag.
Before deployment, make sure that no one is inside or near the vehicle.
The rear seat airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat airbag assembly RH with a deployed airbag.
Do not apply water, etc. to a rear seat airbag assembly RH with a deployed airbag.
Always wash your hands with water after completing the operation.
The airbag is deployed as the LED of the SST activation switch comes on.
3.DISPOSE OF REAR SEAT AIRBAG ASSEMBLY RH (When not Installed to Vehicle)
Be sure to perform the following procedure when deploying the airbag.
Prepare a 12 V battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Remove the rear seat airbag assembly RH.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>REAR SEAT SIDE AIRBAG ASSEMBLY (for RH Side)>REMOVAL
|
Deployment Side |
When storing the rear seat airbag assembly RH, keep the airbag deployment side facing upward.
| *a | Wire Diameter |
| *b | Stripped Wire Cross Sectional Area |
Using braided wire, tie down the rear seat airbag assembly RH to an unneeded tire.
Stripped Wire Cross Sectional Area
1.25 mm2 (0.0019 in.2) or more
If the wire is too thin or an alternative object is used to tie down the rear seat airbag assembly RH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).
To calculate the cross sectional area of the stripped wire:
Cross sectional area = 3.14 x (Diameter)2 / 4
Install the 2 nuts to the rear seat airbag assembly RH.
Wind 2 or more wires around the stud bolts of the rear seat airbag assembly RH as shown in the illustration.
| *a | Inner Diameter |
| *b | Width |
Position the rear seat airbag assembly RH inside the tire with the airbag deployment side facing inward.
185 mm (7.28 in.)
360 mm (1.18 ft.)
Make sure that the wires are tight. If there is slack in the wires, the rear seat airbag assembly RH may break loose when the airbag is deployed.
|
Deployment Side |
Always tie down the rear seat airbag with the airbag deployment side facing inside the tire as shown in the illustration.
The tire may be damaged by the airbag deployment, so use an unneeded tire.
Install SST.
Connect the SST connector to the rear seat airbag assembly RH connector.
Place the tires.
| *a | Tires (2 or more) |
| *b | Inner Diameter |
| *c | Width |
Place at least 2 tires under the tire to which the rear seat airbag assembly RH is tied.
185 mm (7.28 in.)
360 mm (1.18 ft.)
Do not place the SST connector under the tire because it could be damaged.
Place at least 2 tires onto the tire to which the rear seat airbag assembly RH is tied. The top tire should have a wheel installed.
The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.
Tie the tires together with 2 wires.
Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.
Install SST.
| *a | Battery |
| *b | 10 m (32.8 ft.) or more |
Connect the SST connector.
To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.
Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.
Deploy the airbag.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the rear seat airbag assembly RH is tied.
Press the SST activation switch to deploy the airbag.
Before deployment, make sure that no one is near the airbag.
The airbag is deployed as the LED of the SST activation switch comes on.
Dispose of the rear seat airbag assembly RH.
The rear seat airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat airbag assembly RH with a deployed airbag.
Do not apply water, etc. to a rear seat airbag assembly RH with a deployed airbag.
Always wash your hands with water after completing the operation.
Remove the rear seat airbag assembly RH from the tire.
Place the rear seat airbag assembly RH in a plastic bag, tie it tightly, and dispose of it according to local regulations.