The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat assembly removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback spring sub-assembly, front seatback pad and front seatback cover sub-assembly with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1. PRECAUTION
|
|
71910F 2.REMOVE FRONT SEAT HEADREST ASSEMBLY LH
72123M 3.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Operate the slide and vertical power seat switch knob to move the front seat assembly LH to the rearmost position.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and slide in the removal direction (2) while pulling in the removal direction (1) to detach the guide and remove the front outer seat track bracket cover LH.
72123L 4.REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH
Use the same procedure described for the front outer seat track bracket cover LH.
72137Y 5.REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH
| *a | Protective Tape | - | - |
|
Remove in this Direction | - | - |
72158F 6.REMOVE REAR INNER SEAT TRACK BRACKET COVER LH
Use the same procedure described for the rear outer seat track bracket cover LH.
7.REMOVE FRONT SEAT ASSEMBLY LH
Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.
Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the rearmost position.
Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.
Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the center position.
Operate the reclining power seat switch knob to set the seatback of the front seat assembly LH to the perpendicular position.
Operate the slide and vertical power seat switch knob to set the seat cushion height and vertical position of the front seat assembly LH to the highest position.
w/ Front Seat Side Airbag:
1. Disconnect the cable from the negative (-) battery terminal.
for 1GR-FE:
Click hereGeneral>MAINTENANCE>1GR-FE BATTERY>REMOVAL
for V35A-FTS:
Click hereGeneral>MAINTENANCE>V35A-FTS BATTERY>REMOVAL
for F33A-FTV:
Click hereGeneral>MAINTENANCE>F33A-FTV BATTERY>REMOVAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal.
If the airbag deploys for any reason, it may cause a serious accident.
| *A | w/ Front Seat Side Airbag | *B | for LH Side or w/ Rear Seat Entertainment System |
w/ Front Seat Side Airbag:
1. Disconnect the connector of the front seat airbag assembly LH.
Do not pull while holding the wire harness.
Refer to How to Connect or Disconnect Airbag Connector.
for LH Side or w/ Rear Seat Entertainment System:
1. Disconnect the 2 connectors.
Disconnect each connector and detach the clamp.
Remove and carry the front seat assembly LH out of the vehicle.
Protect the front seat legs.
Protect the television display assembly.
Carrying the front seat assembly LH from the vehicle must be performed by multiple people.
Do not damage the front seat assembly LH, body exterior or interior parts.