| *A | w/ Child Restraint System Guide | *B | w/o Child Restraint System Guide |
| *C | w/o Wire Harness | - | - |
| *1 | REAR NO. 1 SEAT CUSHION PAD RH | *2 | HOG RING |
| ● | Non-reusable part | - | - |
| *A | w/ Wire Harness | *B | w/ Rear Seat Side Airbag |
| *C | w/ Child Restraint System Guide | - | - |
| *1 | NO. 1 SEATBACK PAD RH | *2 | SPRING NUT |
| *3 | NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY RH | *4 | HOG RING |
| *5 | PLATE WASHER | *6 | RIVET |
| ★ | Precoated part | ● | Non-reusable part |
71834S 1.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
|
Remove in this Direction | - | - |
Using moulding remover D, detach the clip, claw and guide as shown in the illustration.
Using moulding remover D, detach the claw and guide as shown in the illustration.
Using moulding remover D, detach the claw and guide as shown in the illustration.
Using moulding remover D, detach the claw and guide as shown in the illustration.
Detach the guide and remove the rear No. 1 seat reclining cover LH as shown in the illustration.
72329F 2.REMOVE REAR SEAT ADJUSTER BOLT COVER
72525R 3.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
71833S 4.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Follow the procedure below to detach the claw, clip and guide.
1. Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the clip, claw and guide.
2. Place your hand at the position shown in the illustration and pull in the removal direction (2) to detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Follow the procedure below to remove the rear No. 1 seat reclining cover RH.
1. Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the claw.
2. Place your hand at the position shown in the illustration and pull in the removal direction (2) to detach the claw and guide.
3. Place your hands at the position shown in the illustration and pull in the removal direction (3) to detach the guide and remove the rear No. 1 seat reclining cover RH.
78950F 5.REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
|
Open in this Direction | - | - |
76971G 6.REMOVE REAR UNDER COVER
79952A 7.REMOVE NO. 1 SEAT NO. 2 CUSHION COVER
|
Remove in this Direction | - | - |
79951B 8.REMOVE NO. 1 SEAT NO. 1 CUSHION COVER
|
Remove in this Direction | - | - |
79967W 9.REMOVE REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
|
Remove in this Direction | - | - |
Use the same procedure for the other side.
82193 10.REMOVE REAR SEAT WIRE RH (w/o Wire Harness)
|
Remove in this Direction | - | - |
71302C 11.REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
71301G 12.REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
| *A | w/ Wire Harness | - | - |
|
Remove in this Direction | - | - |
72995F 13.REMOVE REAR SEAT CUSHION COVER RH
72927F 14.REMOVE REAR SEAT CUSHION UNDER COVER RH
73350 15.REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
73380C 16.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73310D 17.DISCONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (SEAT ANCHOR)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
72996H 18.REMOVE REAR SEATBACK COVER (w/ Child Restraint System Guide)
|
Remove in this Direction | - | - |
72996J 19.REMOVE REAR NO. 2 SEATBACK COVER (w/ Child Restraint System Guide)
|
Remove in this Direction | - | - |
71701A 20.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH
21.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH
The illustrations are representative examples, and details may differ.
| *A | w/ Wire Harness | - | - |
| *a | Hole | - | - |
|
Remove in this Direction | - | - |
w/ Wire Harness:
1. Disconnect each connector and the clamp.
2. Thread the wire harness down through the hole in the No. 1 seatback pad RH and rear No. 1 seat cushion pad RH.
Detach the hook.
Remove the separate type rear seat cushion assembly RH as shown in the illustration.
71075F 22.REMOVE NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY RH
|
|
| *A | w/ Child Restraint System Guide | *B | w/o Child Restraint System Guide |
|
Fastener | - | - |
w/ Child Restraint System Guide:
1. Remove the 12 hog rings and 2 fasteners.
w/o Child Restraint System Guide:
1. Remove the 8 hog rings.
Using a thin-bladed screwdriver, detach the claw to remove the No. 1 seat cushion cover sub-assembly LH from the rear No. 1 seat cushion pad LH as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
71751D 23.REMOVE REAR SEAT COVER HANGER (w/ Rear Seat Side Airbag)
73178A 26.REMOVE SEAT BELT ANCHOR COVER CAP
73373 27.REMOVE REAR SEAT SHOULDER BELT COVER
|
Remove in this Direction | - | - |
71930Q 28.REMOVE REAR SEAT HEADREST SUPPORT ASSEMBLY
29.REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH
|
Remove in this Direction | - | - |
79013D 30.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH
|
|
Remove the 6 hog rings.
Using a thin-bladed screwdriver, detach the claw to remove the No. 1 seatback cover sub-assembly RH from the No. 1 seatback pad RH as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
73310D 31.REMOVE REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY
79117D 32.REMOVE NO. 1 SEAT CUSHION CARPET (w/ Child Restraint System Guide)
| *a | Fastener | - | - |
|
Remove in this Direction | - | - |
71694G 33.REMOVE REAR INNER SEAT CUSHION HINGE COVER LH
71485E 34.REMOVE REAR SEAT HINGE COVER
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) | - | - |
Follow the procedure below to remove the rear seat hinge cover.
1. Pull in the removal direction (1) to detach the claw and guide as shown in the illustration.
2. Pull in the removal direction (2) to detach the claw and guide as shown in the illustration.
3. Pull in the removal direction (3) to detach the guide and remove the rear seat hinge cover as shown in the illustration.
71H76L 35.REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH
71H75L 36.REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH
72552K 37.REMOVE SEAT RECLINING HINGE COVER RH
72551M 38.REMOVE SEAT RECLINING HINGE COVER RH
72569B 39.REMOVE SEATBACK STOPPER PLATE
71486F 40.REMOVE REAR SEAT HINGE COVER LH
79103B 41.REMOVE NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH
| *a | Cable End | - | - |
|
Remove in this Direction |
|
Bolt |
|
"TORX" Bolt | - | - |
Detach each casing cap.
Turn each cable end in the removal direction shown in the illustration and disconnect the cable end.
Remove the 3 bolts.
Using a T55H wrench torx for tamper resistant, remove the 2 "TORX" bolts and No. 1 seatback frame sub-assembly RH.
72307D 42.REMOVE NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY RH
71461H 43.REMOVE REAR SEAT CUSHION SPRING
Use the same procedure for the other side.
72143D 44.REMOVE REAR SEAT LOWER TRACK BRACKET RH
72660P 45.REMOVE REAR SEAT LOCK ASSEMBLY LH
| *a | Cable End | - | - |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the casing cap.
Turn the cable end in the removal direction (1) shown in the illustration and disconnect the cable end.
Slide in the removal direction (2) shown in the illustration to remove the rear seat lock assembly LH.
72650J 46.REMOVE REAR SEAT LOCK ASSEMBLY RH
| *a | Cable End | - | - |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the nut and plate washer.
Detach the casing cap.
Turn the cable end in the removal direction (1) shown in the illustration and disconnect the cable end.
Slide in the removal direction (2) shown in the illustration to remove the rear seat lock assembly RH.
72570E 47.REMOVE NO. 1 SEAT RECLINING ADJUSTING CABLE ASSEMBLY RH
78910C 48.REMOVE SEAT FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
82193 49.REMOVE REAR SEAT WIRE RH (w/ Wire Harness)
The illustrations are representative examples, and details may differ.