| *A | w/ Wire Harness | *B | w/ Rear Seat Side Airbag |
| *C | w/ Child Restraint System Guide | - | - |
| *1 | NO. 1 SEATBACK PAD RH | *2 | SPRING NUT |
| *3 | NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY RH | *4 | HOG RING |
| *5 | PLATE WASHER | *6 | RIVET |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
|
Toyota Genuine Adhesive 1324, Three Bond 2468 or equivalent. | ★ | Precpated part |
| ● | Non-reusable part | - | - |
| *A | w/ Child Restraint System Guide | *B | w/o Child Restraint System Guide |
| *C | w/o Wire Harness | - | - |
| *1 | REAR NO. 1 SEAT CUSHION PAD RH | *2 | HOG RING |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
82193 1.INSTALL REAR SEAT WIRE RH (w/ Wire Harness)
78910C 2.INSTALL SEAT FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
72570E 3.INSTALL NO. 1 SEAT RECLINING ADJUSTING CABLE ASSEMBLY RH
72650J 4.INSTALL REAR SEAT LOCK ASSEMBLY RH
72660P 5.INSTALL REAR SEAT LOCK ASSEMBLY LH
72143D 6.INSTALL REAR SEAT LOWER TRACK BRACKET RH
71461H 7.INSTALL REAR SEAT CUSHION SPRING
72307D 8.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY RH
79103B 9.INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH
| *a | Cable End | - | - |
|
Install in this Direction |
|
Bolt |
|
"TORX" Bolt | - | - |
Clean the bolt holes in the No. 1 seat cushion frame sub-assembly RH.
Apply adhesive to the threads of the 2 "TORX" bolts in the area shown in the illustration.
Toyota Genuine Adhesive 1324, Three Bond 2468 or equivalent.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 2.5 to 5.5mm | B | 10.5 to 13.5mm |
Temporarily install the No. 1 seatback frame sub-assembly RH with the 3 bolts and 2 "TORX" bolts.
While pushing in the direction shown in the illustration, using a T55H wrench torx for tamper resistant, install the No. 1 seatback frame sub-assembly RH with the 2 "TORX" bolts in the order shown in the illustration.
While pushing in the direction shown in the illustration, tighten the 3 bolts.
Turn each cable end in the installation direction shown in the illustration and connect each cable end.
Attach each casing cap.
71486F 10.INSTALL REAR SEAT HINGE COVER LH
72569B 11.INSTALL SEATBACK STOPPER PLATE
72551M 12.INSTALL SEAT RECLINING HINGE COVER RH
72552K 13.INSTALL SEAT RECLINING HINGE COVER RH
71H75L 14.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH
71H76L 15.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH
71485E 16.INSTALL REAR SEAT HINGE COVER
71694G 17.INSTALL REAR INNER SEAT CUSHION HINGE COVER LH
79117D 18.INSTALL NO. 1 SEAT CUSHION CARPET (w/ Child Restraint System Guide)
| *1 | NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH | - | - |
| *a | Fastener | - | - |
|
Install in this Direction | - | - |
Follow the procedure below to install the No. 1 seat cushion carpet.
1. Pass the slit part of the No. 1 seat cushion carpet through the wire part of No. 1 seatback frame sub-assembly RH.
2. Wrap the No. 1 seat cushion carpet around the pipe of the No. 1 seatback frame sub-assembly RH and attach it with a fastener as shown in the illustration.
79013D 20.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY RH
21.INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH
71930Q 22.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
73373 23.INSTALL REAR SEAT SHOULDER BELT COVER
73178A 24.INSTALL SEAT BELT ANCHOR COVER CAP
71075F 28.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY RH
29.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH
71701A 30.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH
72996J 31.INSTALL REAR NO. 2 SEATBACK COVER (w/ Child Restraint System Guide)
72996H 32.INSTALL REAR SEATBACK COVER (w/ Child Restraint System Guide)
73310D 33.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (SEAT ANCHOR)
73350 35.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
72927F 36.INSTALL REAR SEAT CUSHION UNDER COVER RH
|
Screw A |
|
Screw B |
|
Screw C |
|
Clip |
Install the rear seat cushion under cover RH with the screw A.
Install the screw B.
Install the 7 screws C.
Attach the J hook of the No. 1 seat cushion cover sub-assembly RH.
72995F 37.INSTALL REAR SEAT CUSHION COVER RH
71301G 38.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
71302C 39.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
82193 40.INSTALL REAR SEAT WIRE RH (w/o Wire Harness)
79967W 41.INSTALL REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
79951B 42.INSTALL NO. 1 SEAT NO. 1 CUSHION COVER
79952A 43.INSTALL NO. 1 SEAT NO. 2 CUSHION COVER
76971G 44.INSTALL REAR UNDER COVER
78950F 45.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
71833S 46.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
72525R 47.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
|
Pushed Place |
|
Push in this Direction |
While pressing the reclining adjuster release handle RH as shown in the illustration, install the reclining adjuster release handle RH with the screw.
72329F 48.INSTALL REAR SEAT ADJUSTER BOLT COVER
71834S 49.INSTALL REAR NO. 1 SEAT RECLINING COVER LH