Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P208A19  Reductant Pump "A" Control Circuit High Circuit Current Above Threshold  P208A96  Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure  P20E900  Reductant Pressure Too High  


DESCRIPTION

Refer to DTC P203A96.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P203A96

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P208A19 Reductant Pump "A" Control Circuit High Circuit Current Above Threshold When power is supplied to the urea pump (during normal/reverse operation, power supplied to heater, position fixed), the pump current is equal to or greater than a fixed value.
(1 trip detection logic)
Urea pump Comes on SAE Code: P208D
P208A96 Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure When each pump status is "operating" (operation check, filling, pressure increase, pressure maintenance, line pressure relief), urea pump rotation malfunctions, pressure malfunctions, etc., are detected multiple times.
(1 trip detection logic)
Urea pump Comes on SAE Code: P208B
P20E900 Reductant Pressure Too High After filling the urea injector with urea solution from the urea pipe, the urea pressure is continuously higher than a fixed value.
(1 trip detection logic)
Urea pump Comes on SAE Code: P20E9

Related Data List
DTC No. Data List
P208A19
P208A96
P20E900
Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P208A19
P208A96
P20E900
Idle engine for 5 second

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P208A19, P208A96 OR P20E900)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P208A19, P208A96 or P20E900 is output A
DTC P208A19, P208A96 or P20E900 and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK AROUND BOTTOM OF VEHICLE

B

GO TO DTC CHART

2.CHECK AROUND BOTTOM OF VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector assembly.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.



b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
4.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
a.

Start the engine and idle it for 5 seconds or more.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for 30 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 372 85

e.

Perform the Active Test.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.

Powertrain > Engine > Active Test
Tester Display
Reductant Purge
50004 372 86

g.

Perform the Active Test.

HINT:

Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector assembly.



h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.


Result:
Result Proceed to
No DTCs are output A
DTC P208A19, P208A96 or P20E900 is output B



A

5.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))

B

6.REPLACE UREA PUMP
5.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))
a.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.

Powertrain > Engine > Active Test
Active Test Display
Reductant Filling (Pressure Keep)
Data List Display
Reductant Pressure
50004 372 84 1030

b.

Execute "Reductant Filling (Pressure Keep)


c.

Check the Reductant Pressure.

OK:

450 to 550 kPa


HINT:

During a malfunction, pressure either does not increase, or increases to 800 kPa or higher and then stops.



Result:
Proceed to
OK
NG



OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

6.REPLACE UREA PUMP
6.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and idle it for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END