Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P24521C  Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P245211.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P245211

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P24521C Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range When the output voltage from the differential pressure sensor indicates a reversal of positive and negative pressure.
(1 trip detection logic)
·

Incorrect air hose routing

·

Air hose is clogged

·

Blockage in vacuum pipe

·

Differential pressure sensor

·

ECM


Comes on SAE Code: P2453

Related Data List
DTC No. Data List
P24521C Particulate Filter Differential Pressure Bank 1

HINT:
·

If the air hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P24521C (Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range) is stored and the MIL illuminates.

·

DTC P245211 (Particulate Filter Pressure Sensor "A" Circuit Short to Ground) and/or DTC P245215 (Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open) will be stored if there is an open or short malfunction in the differential pressure sensor circuit.

·

After confirming DTC P24521C, check the differential pressure in "Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1" using the GTS.


Reference:
Condition Particulate Filter Differential Pressure Bank 1 Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect air hose arrangement of the sensor, or determines that the air hoses are clogged, and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24521C Engine is running at 4000 rpm with no load for 10 seconds or more

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P24521C)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P24521C is output A
DTC P24521C and other DTCs are output B


HINT:

If any DTCs other than P24521C are output, troubleshoot those DTCs first.




A

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

B

GO TO DTC CHART

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
A490881C01
4.125,0.333 5.896,0.896 5.896,0.896 6.115,0.896 true 3.979,0.604 1.802,1.333 1.802,1.333 4.135,0.74 true 3.865,1.396 5.021,2.479 5.021,2.479 3.646,1.365 true 6.188,0.844 6.5,1 0.313,0.156 10 false *1 1.635,1.302 1.948,1.458 0.313,0.156 10 false *2 5.073,2.458 5.385,2.615 0.313,0.156 10 false *3
*1 Differential Pressure Sensor *2 Air Hose
*3 Vacuum Pipe - -


a.

Check if the air hose routing between the differential pressure sensor and vacuum pipe is correct.


b.

Check that there is no exhaust gas leakage between the differential pressure sensor and vacuum pipe.


Result:
Proceed to
OK
NG



OK

3.CHECK AIR HOSE AND VACUUM PIPE

NG

8.CORRECT TO NORMAL CONNECTION
3.CHECK AIR HOSE AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.
A490882C01
2.927,1.135 0.563,1.01 0.563,1.01 2.125,0.885 true 0.333,0.948 0.625,1.135 0.292,0.188 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

NG

7.REPLACE CLOGGED PARTS
4.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Turn the ignition switch to ON (engine stopped).


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Check that the "Particulate Filter Differential Pressure Bank 1" is as specified below.

Result
Switch Condition Particulate Filter Differential Pressure Bank 1 Sensor Condition
Ignition switch ON Approximately 0 kPa Normal


Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.REPLACE DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

d.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition Particulate Filter Differential Pressure Bank 1
2500 rpm without load 0.5 kPa or higher




e.

Start the engine.


f.

Run the engine at 4000 rpm with no load for 10 seconds or more.


g.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P24521C.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, run the engine at 4000 rpm with no load for 10 seconds or more.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE CLOGGED PARTS
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CORRECT TO NORMAL CONNECTION
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED