Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) J

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  After Treatment Control System  


CAUTION / NOTICE / HINT

NOTICE:

After replacing the front exhaust pipe sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION


PROCEDURE

1.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 1)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust.


c.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)
2.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)
a.

Check Catalyst Differential Pressure Bank 1 in the snapshot taken in procedure 1 when the engine was running at 4000 rpm with no load.

Result:
Result Proceed to
Catalyst Differential Pressure Bank 1 is more than 0.32 A
Except above B




A

3.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)

B

5.PERFORM PM FORCED REGENERATION
3.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)
a.

Replace the front exhaust pipe sub-assembly (DPF catalyst).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (for Rear Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION
4.PERFORM CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION
a.

Enter the following menus: Powertrain / Engine / Utility / Catalyst Deterioration Learning Value Clear.

Powertrain > Engine > Utility
Tester Display
Catalyst Deterioration Learning Value Clear
50005 372 4568

b.

Press "Next".


c.

Press "Exit".


d.

Enter the following menus: Powertrain / Engine / Utility / DPF Deposition Value Clear.

Powertrain > Engine > Utility
Tester Display
DPF Deposition Value Clear
50005 372 4574

e.

Press "Next".


f.

Press "Exit".


Result:
Proceed to
NEXT



NEXT

5.PERFORM PM FORCED REGENERATION
5.PERFORM PM FORCED REGENERATION
a.

Turn the ignition switch to ON.


b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Connect the GTS to the DLC3.


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




g.

Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode

Powertrain > Engine > Utility
Tester Display
PM Regenerate Mode
50005 372 4576

h.

Enter PM Regenerate Mode.

CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.


HINT:

When PM Accumulation Ratio Bank 1 is too low, Activate the PM forced regeneration cannot be performed. Therefore, rev the engine with no load at 3400 rpm for 5 to 10 minutes to increase PM Accumulation Ratio Bank 1 to 12% or more.



i.

After 10 minutes have passed with the Coolant Temperature at 80°C (176°F) or higher during PM regeneration, check the value of Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
Exhaust Temperature B1S2
50003 372 205,1134
HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio Bank 1" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Pressure Bank 1" increases too much during the PM forced regeneration, the failsafe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal or clutch pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.

·

*1: If Exhaust Temperature B1S2 does not reach 500°C or higher, the exhaust fuel addition injector assembly may be blocked by accumulated deposits.

·

*2: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DOC catalyst.




Result:
Result Proceed to
Exhaust Temperature B1S2 is 500°C (932°F) or less and no white smoke is generated*1 A
Exhaust Temperature B1S2 is 500°C (932°F) or less and abnormal white smoke is generated*2 B
Exhaust Temperature B1S2 reaches 500°C (932°F) or higher C



A

REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DOC CATALYST)

C

END