Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) J

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Lack of Power (Turbocharger System)  


CAUTION / NOTICE / HINT

HINT:
·

The diagnosis flowchart is for lack of power due to turbocharger factors.

·

If symptom-specific diagnosis indicates a turbocharger related problem, check using this flowchart.



PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that no soot or oil adheres to the turbocharger sub-assembly connectors.

A490896

HINT:

If adhering soot or an oil leak exists, air leaking at that position may be the cause of the lack of boost pressure.



Result:
Result Proceed to
No adhering soot or an oil A
Soot adhering around the turbine housing, flange, or exhaust pipe clamp B
Oil leak from the contact surface between the compressor housing and bearing housing C



A

2.CHECK INTAKE/EXHAUST SWITCH VALVE

B

6.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

2.CHECK INTAKE/EXHAUST SWITCH VALVE
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Bypass Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the Air Bypass Valve
50004 372 42039

b.

Turn the Active Test ON and OFF, and check that the air bypass valve makes an operating sound.

HINT:
·

When turning the air bypass valve from ON to OFF, the valve makes a sitting sound.

·

If it is difficult to distinguish the operating sound, repeat the Active Test and check again.

·

If no DTC related to the air bypass valve is output and an operating sound cannot be confirmed, the air bypass valve is stuck.



Result:

There is an operating sound



c.

Inspect the exhaust control valve (No. 2 turbocharger sub-assembly).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>ON-VEHICLE INSPECTION



Result:
Proceed to
OK
NG



OK

3.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace malfunctioning parts in the intake/exhaust system.



3.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that the turbine shaft rotates smoothly, without catching.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION


b.

Check for loose turbine mounting nuts and for axial play in the turbine shaft.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION

HINT:

If the turbine shaft catches or if there no play or excessive play, it could indicate a seal problem due to seizing or poor sliding due to a deposit build up.



Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B



A

4.INSPECT TURBOCHARGER SUB-ASSEMBLY

B

4.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION

HINT:

When there is interference between the turbine wheel and turbine housing and the turbine wheel is damaged, check for fragments of the turbine wheel in the exhaust manifold converter sub-assembly.



Result:
Result Proceed to
No damage or interference A
Damage or interference exists B



A

5.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

5.INSPECT TURBOCHARGER NOZZLE VANE PLATE
a.

Loosen the installation bolt of the turbocharger nozzle vane control actuator.

A491960C01
0.323,0.396 0.635,0.552 0.313,0.156 10 false *1 4.125,0.406 4.438,0.563 0.313,0.156 10 false *2 0.531,0.667 0.844,0.823 0.313,0.156 10 true *3 1.719,0.927 2.031,1.083 0.313,0.156 10 true *4 0.969,0.844 1.281,1 0.313,0.156 10 true *3 1.406,0.625 1.719,0.781 0.313,0.156 10 true *3 5.781,0.833 6.094,0.99 0.313,0.156 10 true *3 6.281,1.031 6.594,1.188 0.313,0.156 10 true *3 6.74,0.813 7.052,0.969 0.313,0.156 10 true *3 5.156,0.906 5.469,1.063 0.313,0.156 10 true *4
*1 No. 1 Turbocharger Sub-assembly *2 No. 2 Turbocharger Sub-assembly
*3 Installation Bolt *4 E-washer



b.

Remove the e-washer from the turbocharger nozzle vane control actuator.


c.
A490876

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

6.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter sub-assembly and the turbocharger sub-assembly.

HINT:

Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.


Standard:

No deformation or cracks on a mounting surface.


Result:
Result Proceed to
No problem with the mounting surface A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface B
Deformation or cracks on the turbocharger sub-assembly mounting surface C




A

7.REPLACE EXHAUST PIPE CLAMP AND GASKET

B

C

7.REPLACE EXHAUST PIPE CLAMP AND GASKET
a.

Replace the exhaust pipe clamp and the gasket.


Result:
Proceed to
NEXT



NEXT

8.PERFORM SIMULATION TEST
8.PERFORM SIMULATION TEST
a.

Check that the abnormal state has disappeared.


Result:
Proceed to
NEXT



NEXT

END