Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P059A71  Active Grille Air Shutter "A" Actuator Stuck  P059A79  Active Grille Air Shutter "A" Mechanical Linkage Failure  


DESCRIPTION

The ECM communicates with the swing grille actuator via LIN communication.

When the certain vehicle conditions are met, the ECM operates the swing grille actuator to open and close the radiator shutter and control the volume of air flowing through the radiator into the engine compartment. This results in increased thermal efficiency and increased fuel economy due to reduced aerodynamic drag. This control is performed based on signals received via CAN communication: vehicle speed signal, engine coolant temperature signal, ambient temperature signal and refrigerant pressure.

Control List
Control Description
Closing Operation Control When the grille shutter is open and the vehicle conditions are met, the grille shutter closes in order to improve fuel economy (reduce air resistance) and reduce engine warm up time.
Opening Operation Control When the grille shutter is closed and the vehicle conditions are met, the grille shutter opens to ensure radiator and engine cooling air.
Ignition Switch Off-linked Opening Operation Control When the ignition switch is turned off and the vehicle is stopped with the grille shutter closed, the grille shutter opens.
Snow Blockage Control Operation If the vehicle is driven in a cold environment where the grille shutter may be frozen and stuck closed, the malfunction threshold will be set higher than usual.
Retry Operation If a mechanical malfunction is detected during a grille shutter operation, the operation will be attempted again.

A473418E06
3.948,0.604 4.292,0.354 4.292,0.354 4.479,0.354 false 4.563,0.271 6.594,1.281 2.031,1.01 10 false Grille Shutter Motor 3.396,1.417 4.875,1.844 1.479,0.427 10 false Motor Drive Circuit 3.573,2.375 5.052,2.802 1.479,0.427 10 false Motor Drive 3.26,3.229 4.646,3.688 1.385,0.458 10 false Power Supply Voltage Monitor Circuit 3.323,4.583 4.708,5.042 1.385,0.458 10 false Power Supply Circuit 0.302,4.698 1.594,5.333 1.292,0.635 10 false from GRILLE SHUTT fuse 1.896,4.51 2.771,5.052 0.875,0.542 10 false +B 1.802,5.198 2.677,5.74 0.875,0.542 10 false GND 1.854,6.073 2.729,6.615 0.875,0.542 10 false LIN 3.323,5.938 4.563,6.5 1.24,0.563 10 false LIN Communication Circuit 0.865,6.24 2.104,6.802 1.24,0.563 10 false to ECM 5.656,3.99 6.417,4.385 0.76,0.396 10 false CPU 3.573,7.698 5.354,8.156 1.781,0.458 10 false Swing Grille Actuator 0.49,8.417 2.229,8.656 1.74,0.24 10 false : LIN Communication Line

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P059A71 Active Grille Air Shutter "A" Actuator Stuck A signal from the swing grille actuator assembly indicating that the grille shutter is stuck is detected for 7.86 seconds or more (2 trip detection logic).
·

Radiator shutter assembly

·

ECM


Does not come on SAE Code: P059F
P059A79 Active Grille Air Shutter "A" Mechanical Linkage Failure A signal from the swing grille actuator assembly indicating a malfunction is detected for 7.86 seconds or more (2 trip detection logic).
·

Radiator shutter assembly

·

ECM


Does not come on SAE Code: P059F

MONITOR DESCRIPTION

When the swing grille actuator assembly detects that the grille shutter is stuck or there is a malfunction, a DTC request is sent to the ECM and the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P059A71
P059A79
Select Switch Grille Shutter Control Mode from the Utility menu of the GTS and switch to the maintenance mode.
Select Grille Shutter Initialization from the Utility menu of the GTS and perform initialization (nominal torque) .

CAUTION / NOTICE / HINT

NOTICE:

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

Result:
Proceed to
NEXT



NEXT

2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

No foreign matter or ice.



Result:
Proceed to
OK
NG



OK

3.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)

NG

6.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
a.

According to the display on the GTS, perform initialization (nominal torque).

Powertrain > Engine > Utility
Tester Display
Grille Shutter Initialization
50005 372 5673

Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (DTC P059A71 OR P059A79)
5.CHECK DTC OUTPUT (DTC P059A71 OR P059A79)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P059A71 and/or P059A79 is output B



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION



A

8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

B

REPLACE RADIATOR SHUTTER ASSEMBLY

6.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal


Result:
Proceed to
NEXT




NEXT

END