Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P07707F  Shift Solenoid "E" Actuator Stuck Off  


DESCRIPTION

Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.

If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).

HINT:
Actual gear shift position when a malfunction occurs in solenoid (SR) valve:
TCM Commanded Gear Actual Gear during SR Stuck OFF Malfunction
1st 1st
2nd 2nd
3rd 3rd
4th 4th
5th 7th or 10th
6th 7th or 9th
7th 7th or 9th
8th 8th
9th 7th or 9th
10th 7th or 10th


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07707F Shift Solenoid "E" Actuator Stuck Off The vehicle is driven with the shift lever in D and one of the following conditions is met (2-trip detection logic):
·

When the TCM commands the transmission to shift to 5th, the actual gear changes to 7th or 10th gear.

·

When the TCM commands the transmission to shift to 6th, the actual gear changes to 7th or 9th gear.

·

When the TCM commands the transmission to shift to 7th, the actual gear changes to 9th gear.

·

When the TCM commands the transmission to shift to 9th, the actual gear changes to 7th gear.

·

When the TCM commands the transmission to shift to 10th, the actual gear changes to 7th gear.

·

When the TCM commands the transmission to shift to 5th or higher and the TCM commands lock-up ON, the difference between the turbine speed (NT) and the engine speed (NE) is 70 rpm or more for 2 seconds or more.


·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SC1) valve

·

Solenoid (SL) valve

·

Solenoid (SR) valve

·

Solenoid (SLU) valve

·

Solenoid (SLT) valve

·

Transmission valve body assembly

·

Torque converter assembly

·

Automatic transmission assembly (clutch, brake, gear, etc.)


Comes on DTC stored SAE: P0771

DTC Detection Condition Patterns
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnostic Condition The vehicle is driven with the shift lever in D. ○ ○ ○ ○ ○ ○
Malfunction Condition When the TCM commands the transmission to shift to 5th, the actual gear changes to 7th or 10th gear. ○ - - - - -
When the TCM commands the transmission to shift to 6th, the actual gear changes to 7th or 9th gear. - ○ - - - -
When the TCM commands the transmission to shift to 7th, the actual gear changes to 9th gear. - - ○ - - -
When the TCM commands the transmission to shift to 9th, the actual gear changes to 7th gear. - - - ○ - -
When the TCM commands the transmission to shift to 10th, the actual gear changes to 7th gear. - - - - ○ -
When the TCM commands the transmission to shift to 5th or higher and the TCM commands lock-up ON, the difference between the turbine speed (NT) and the engine speed (NE) is 70 rpm or more. - - - - - ○
Duration - - - - - 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the solenoid valves on and off. According to the input shaft revolution (speed) and output shaft revolution (speed), the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th, 8th, 9th or 10th gear position). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P07707F.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P07707F)
a.

Read the DTCs using the GTS.

Powertrain > Transmission > Trouble Codes
50001 373
Result:
Result Proceed to
DTC P07707F and DTC P07407E, P07457F, P076A71, P07757F, P07957F, P08BA7F, P27137F, P27567F, P28077F and/or P28167F are output A
Only DTC P07707F is output B
DTCs other than P07407E, P07457F, P076A71, P07707F, P07757F, P07957F, P08BA7F, P27137F, P27567F, P28077F and P28167F are also output C


HINT:

If any DTCs other than P07407E, P07457F, P076A71, P07707F, P07757F, P07957F, P08BA7F, P27137F, P27567F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.




A

2.CLEAR DTC AND PERFORM STALL SPEED TEST

B

3.INSPECT SOLENOID (SL) AND (SR) VALVE

C

GO TO DTC CHART

2.CLEAR DTC AND PERFORM STALL SPEED TEST
a.

Clear the DTCs.

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > Transmission > Clear DTCs
50002 373

b.

Perform the stall speed test.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>MECHANICAL SYSTEM TESTS

Result:
Test Condition Proceed to
Stall speed test can be performed A
Stall speed test cannot be performed B




A

3.INSPECT SOLENOID (SL) AND (SR) VALVE

B

6.INSPECT SOLENOID (SLT) VALVE
3.INSPECT SOLENOID (SL) AND (SR) VALVE
a.
C375005C02
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1
*1 Solenoid (SL) and (SR) Valves


Remove the solenoid (SL) and (SR) valves.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of solenoid (SL) valve connector - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω
Terminal of solenoid (SR) valve connector - Solenoid (SR) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) AND (SLU) VALVE

NG

4.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) AND (SLU) VALVE
a.
C197715C19
1.76,0.969 2.208,0.385 false 1.479,0.958 1.021,0.375 false 1.771,2.958 2.219,2.365 false 1.469,2.948 1.01,2.354 false 0.094,0.083 0.531,0.417 0.438,0.333 10 *1 2.26,0.26 2.427,0.458 0.167,0.198 10 1 0.875,0.24 1.042,0.438 0.167,0.198 10 2 2.271,2.24 2.438,2.438 0.167,0.198 10 1 0.906,2.24 1.073,2.438 0.167,0.198 10 2 1.927,3.927 2.208,4.125 0.281,0.198 10 (+) 1.146,3.938 1.448,4.135 0.302,0.198 10 (-)
*1 Solenoid (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) and (SLU) Valves


Remove the solenoid (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) and (SLU) valves.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL1) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL2) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL3) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL4) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL5) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL6) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SLU) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

5.INSPECT SOLENOID (SC1) VALVE

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) OR (SLU) VALVE

5.INSPECT SOLENOID (SC1) VALVE
a.
C375005C02
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1
*1 Solenoid (SC1) Valve


Remove the solenoid (SC1) valve.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of solenoid (SC1) valve connector - Solenoid (SC1) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

6.INSPECT SOLENOID (SLT) VALVE

NG

6.INSPECT SOLENOID (SLT) VALVE
a.
C197715C19
1.76,0.969 2.208,0.385 false 1.479,0.958 1.021,0.375 false 1.771,2.958 2.219,2.365 false 1.469,2.948 1.01,2.354 false 0.094,0.083 0.531,0.417 0.438,0.333 10 *1 2.26,0.26 2.427,0.458 0.167,0.198 10 1 0.875,0.24 1.042,0.438 0.167,0.198 10 2 2.271,2.24 2.438,2.438 0.167,0.198 10 1 0.906,2.24 1.073,2.438 0.167,0.198 10 2 1.927,3.927 2.208,4.125 0.281,0.198 10 (+) 1.146,3.938 1.448,4.135 0.302,0.198 10 (-)
*1 Solenoid (SLT) Valve


Remove the solenoid (SLT) valve.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

7.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

7.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

8.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

8.INSPECT TORQUE CONVERTER ASSEMBLY

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter operates normally.


Result:
Proceed to
OK
NG



OK

NG