Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) L

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART





INITIALIZATION AND REGISTRATION


NOTICE:
·

If any parts are replaced, perform the following procedures as necessary referring to the table below.

Replaced Part A/T Code Registration A/T Code Registration (Fixed Code) Learning by Driving (Road Test)
·

Transmission valve body assembly

·

Solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves


- - Perform
TCM
(If possible, read the transmission compensation code from the previous TCM)
Possible Perform* - Perform
Impossible - Perform Perform
Engine assembly - - Perform

HINT:
·

*: Read the transmission compensation code from the previous TCM, then transfer it to the new TCM.



·

If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>INITIALIZATION

-

The ATF has been replaced.

HINT:

If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.


-

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.





HANDLING PRECAUTIONS


CAUTION:
·
C328184


·

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328186


·

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328185


·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328175

Do not blow compressed air without wearing safety glasses.

·

Automatic Transmission Fluid (ATF) could enter your eyes, possibly resulting in blindness.



NOTICE:
·

The automatic transmission is composed of precision-made parts. Careful inspection before reassembly is necessary because even a small nick could cause fluid leakage or affect performance.

·

The procedures are organized so that you work on only one component group at a time. This will help avoid confusion with similar-looking parts of different sub-assemblies being on your workbench at the same time.

·

The component groups are inspected and repaired from the converter housing side.

·

Whenever possible, complete the inspection, repair and reassembly before proceeding to the next component group. If a defect is found in a certain component group during reassembly, inspect and repair this group immediately. If a component group cannot be assembled because parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups.

·

Use of Toyota Genuine ATF WS is recommended.

·

All disassembled parts should be washed clean, and compressed air should be blown through any fluid passages and holes.

·

Dry all parts with compressed air. Never use a piece of cloth.

·

The recommended ATF or kerosene should be used for cleaning.

·

After cleaning, the parts should be arranged in the order they were removed for efficient inspection, repair and reassembly.

·

New discs for the brakes and clutches must be soaked in ATF for at least 15 minutes before reassembly.

·

All oil seal rings, clutch discs, clutch plates, rotating parts, and sliding surfaces should be coated with ATF prior to reassembly.

·

All old gaskets and rubber O-rings must be replaced.

·

Do not apply adhesive cement to gaskets or similar parts.

·

Make sure that the ends of snap rings are not aligned with any cutouts. Make sure that snap rings are correctly installed into the grooves.

·

If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be replaced.

·

Check the thrust bearings and races for wear or damage. Replace them if necessary.

·

Use petroleum jelly to keep parts in place.