Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0484462 AUTOMATIC TRANSMISSION ASSEMBLY(for F33A-FTV) A

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for F33A-FTV)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462088C01
1.417,4.688 3.656,5.708 2.24,1.021 2.99,5.521 2.771,5.521 2.771,5.521 2.604,5.281 false 5.458,5.073 5.458,4.698 false 0.74,4.458 0.74,3.948 false 0.656,0.583 0.979,0.271 0.979,0.271 1.167,0.271 false 4.594,0.177 4.927,0.177 4.927,0.177 5.125,0.396 false 4.802,3.906 5.323,3.906 false 5.427,2.208 5.896,2.208 false 5.76,2.625 6.198,2.625 false 2.906,4.104 3.177,4.104 false 1.625,1.417 1.896,1.417 1.896,1.417 2.042,1.542 false 2.906,3.865 3.115,3.615 3.115,3.615 3.25,3.615 false 2.167,1.594 2.479,1.354 2.479,1.354 2.74,1.354 false 5.26,2.26 5.188,2.417 5.188,2.417 5.438,2.417 false 5.635,2.688 5.802,2.948 5.802,2.948 6.021,2.948 false 2.594,3.979 2.844,3.979 false 6.719,0.24 6.865,0.24 false 5.021,1.604 4.75,1.365 4.75,1.365 4.5,1.365 false 0.635,1.833 0.896,1.833 0.896,1.833 1.208,2.396 false 1.833,0.563 2.01,0.26 2.01,0.26 2.208,0.26 false 5.802,1.417 6.083,1.646 0.281,0.229 10 false x 4 6.083,3.448 6.469,3.688 0.385,0.24 10 false x 4 3.031,5.375 3.26,5.719 0.229,0.344 18 false 1 5.385,5.083 5.667,5.438 0.281,0.354 18 false 2 0.667,4.49 0.948,4.844 0.281,0.354 18 false 6 1.219,0.146 1.5,0.5 0.281,0.354 18 false 4 4.292,1.229 4.5,1.604 0.208,0.375 18 false 8 6.115,0.104 6.729,0.438 0.615,0.333 18 false 7, 10 4.375,0.052 4.604,0.406 0.229,0.354 18 false 3 4.573,3.771 4.813,4.125 0.24,0.354 18 false 9 3.208,4.021 3.427,4.229 0.219,0.208 10 false *1 1.427,1.333 1.635,1.563 0.208,0.229 10 false *2 3.281,3.531 3.49,3.76 0.208,0.229 10 false *3 5.927,2.115 6.177,2.302 0.25,0.188 10 false *4 6.219,2.531 6.469,2.719 0.25,0.188 10 false *5 6.052,2.854 6.25,3.073 0.198,0.219 10 false ● 5.479,2.313 5.656,2.542 0.177,0.229 10 false ● 2.438,3.885 2.615,4.094 0.177,0.208 10 false ● 2.781,1.26 2.969,1.469 0.188,0.208 10 false ● 0.302,1.688 0.646,2.052 0.344,0.365 18 false 11 0.448,2.25 0.833,2.49 0.385,0.24 10 false x 2 1.469,4.729 1.781,4.927 0.313,0.198 10 false *A 2.281,0.135 2.542,0.438 0.26,0.302 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT PROPELLER SHAFT ASSEMBLY 37140 - - -
2 REAR PROPELLER SHAFT ASSEMBLY 37110F - - -
3 CENTER EXHAUST PIPE ASSEMBLY 17420 - - -
4 FRONT EXHAUST PIPE SUB-ASSEMBLY 17401 - - -
5 NO. 2 FRONT EXHAUST PIPE SUB-ASSEMBLY 17402 - - -
6 STARTER ASSEMBLY 28100 - - -
7 DRAIN AUTOMATIC TRANSMISSION FLUID - - (Click here) -
8 TRANSFER HEAT INSULATOR 36336 - - -
9 LOWER TRANSFER CASE PROTECTOR 36179 - - -
10 DRAIN TRANSFER OIL - - (Click here) -
11 OIL PAN COVER SILENCER 12144 - - -

*A w/o Urea SCR System - -
*1 OVERFLOW PLUG *2 REFILL PLUG
*3 NO. 1 TRANSMISSION OIL FILLER TUBE *4 FILLER PLUG
*5 DRAIN PLUG - -
● Non-reusable part - -

C462084C01
0.625,0.604 1.125,0.604 false 2.198,1.135 2.354,0.438 2.354,0.438 2.521,0.438 false 5.063,3.594 5.271,3.906 5.271,3.906 5.531,3.906 false 5.417,2.458 5.938,2.458 false 6.438,1.646 6.438,1.458 6.438,1.458 5.813,1.198 false 0.99,1.021 1.427,1.021 false 3.104,2.531 3.667,2.125 3.667,2.125 3.844,2.125 true 3.688,1.375 4,1.375 false 1.854,2.594 1.854,2.438 1.854,2.438 1.594,2.281 false 0.885,4.625 0.99,4.656 0.99,4.656 1.281,4.656 false 0.99,5.302 0.844,5.479 0.844,5.479 0.604,5.479 true 4.885,5.083 5.135,5.406 5.135,5.406 5.438,5.406 false 3.323,2.021 3.635,2.229 0.313,0.208 10 false x 6 0.26,5.354 0.594,5.677 0.333,0.323 18 true 13 1.635,4.51 2.094,4.875 0.458,0.365 21 false 12 4.031,1.229 4.396,1.563 0.365,0.333 18 false 14 0.26,0.479 0.635,0.813 0.375,0.333 18 false 15 2.885,0.302 3.271,0.646 0.385,0.344 18 false 16 1.708,2.604 2.094,2.958 0.385,0.354 18 false 17 5.885,3.792 6.74,4.125 0.854,0.333 18 false 19, 24 5.49,5.271 5.833,5.604 0.344,0.333 18 false 18 6,2.323 6.375,2.656 0.375,0.333 18 false 21 6.302,1.667 6.688,1.99 0.385,0.323 18 false 23 0.76,4.646 1.031,4.865 0.271,0.219 10 false *a 1.167,0.125 1.479,0.323 0.313,0.198 10 false x 2 1.177,1.74 1.49,1.938 0.313,0.198 10 false x 2 0.823,0.927 1.01,1.167 0.188,0.24 10 false ● 4.177,2.021 4.552,2.354 0.375,0.333 18 false 22 3.25,4.24 3.563,4.438 0.313,0.198 10 false x 4 5.25,0.219 5.542,0.448 0.292,0.229 10 false x 4 3.302,0.906 3.615,1.104 0.313,0.198 10 false x 2 1.229,4.813 1.5,5 0.271,0.188 10 false x 3 0.073,0.052 0.385,0.313 0.313,0.26 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

12 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT 32101A (Click here) - -
13 OIL COOLER TUBE SUB-ASSEMBLY - - - -
14 TRANSMISSION INSULATOR RH 35979B - - -
15 TRANSMISSION CONTROL CABLE INSULATOR 33825 - - -
16 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
17 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
18 FRONT PROPELLER SHAFT ASSEMBLY 37140 - - -
19 SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - (Click here) - -
21 DISCONNECT WIRE HARNESS CLAMP BRACKET - - - -
22 TRANSFER BREATHER HOSE SUB-ASSEMBLY 36407 (Click here) - -
23 WIRE HARNESS - (Click here) - -
24 REMOVE AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - (Click here) - -

*A w/ Urea SCR System - -
*a Black: x 1
Silver: x 5
- -
● Non-reusable part - -

C458280C04
0.625,0.604 1.125,0.604 false 2.198,1.135 2.354,0.438 2.354,0.438 2.521,0.438 false 5.063,3.594 5.271,3.906 5.271,3.906 5.531,3.906 false 3.469,4.625 3.75,4.625 3.75,4.625 3.99,4.375 false 5.417,2.458 5.938,2.458 false 6.438,1.646 6.438,1.458 6.438,1.458 5.813,1.198 false 3.542,5.198 3.979,5.198 false 0.99,1.021 1.427,1.021 false 3.115,2.531 3.667,2.135 3.667,2.135 3.833,2.135 true 3.688,1.375 4,1.375 false 1.854,2.594 1.854,2.438 1.854,2.438 1.594,2.281 false 0.885,4.625 0.99,4.656 0.99,4.656 1.281,4.656 false 0.99,5.302 0.844,5.479 0.844,5.479 0.604,5.479 true 4.125,5.563 4.438,5.76 0.313,0.198 10 false x 4 5.396,5.146 5.708,5.344 0.313,0.198 10 false x 4 4.281,4.854 4.531,5.021 0.25,0.167 10 false x 4 3.323,2.021 3.635,2.229 0.313,0.208 10 false x 6 0.26,5.354 0.594,5.677 0.333,0.323 18 true 13 1.635,4.51 2.031,4.833 0.396,0.323 18 false 12 4.031,1.229 4.396,1.563 0.365,0.333 18 false 14 0.26,0.458 0.635,0.792 0.375,0.333 18 false 15 2.885,0.302 3.271,0.646 0.385,0.344 18 false 16 1.708,2.604 2.094,2.958 0.385,0.354 18 false 18 5.885,3.792 6.74,4.125 0.854,0.333 18 false 19, 24 3.135,4.49 3.469,4.865 0.333,0.375 18 false 20 6,2.323 6.375,2.656 0.375,0.333 18 false 21 6.302,1.667 6.688,1.99 0.385,0.323 18 false 23 0.76,4.646 1.031,4.865 0.271,0.219 10 false *a 1.167,0.125 1.479,0.323 0.313,0.198 10 false x 2 1.177,1.74 1.49,1.938 0.313,0.198 10 false x 2 3.333,5.125 3.542,5.354 0.208,0.229 10 false *1 0.823,0.927 1.01,1.167 0.188,0.24 10 false ● 4.177,2.021 4.552,2.354 0.375,0.333 18 false 22 3.25,4.24 3.563,4.438 0.313,0.198 10 false x 4 5.25,0.219 5.542,0.448 0.292,0.229 10 false x 4 3.302,0.906 3.615,1.104 0.313,0.198 10 false x 2 1.229,4.813 1.5,5 0.271,0.188 10 false x 3 0.052,0.042 0.313,0.271 0.26,0.229 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

12 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT 32101A (Click here) - -
13 OIL COOLER TUBE SUB-ASSEMBLY - - - -
14 TRANSMISSION INSULATOR RH 35979B - - -
15 TRANSMISSION CONTROL CABLE INSULATOR 33825 - - -
16 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
18 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
19 SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - (Click here) - -
20 NO. 3 FRAME CROSSMEMBER ASSEMBLY - - - -
21 DISCONNECT WIRE HARNESS CLAMP BRACKET - - - -
22 TRANSFER BREATHER HOSE SUB-ASSEMBLY 36407 (Click here) - -
23 WIRE HARNESS - (Click here) - -
24 REMOVE AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - (Click here) - -

*A w/o Urea SCR System - -
*1 NO. 3 ENGINE MOUNTING HOLE COVER - -
*a Black: x 1
Silver: x 5
- -
● Non-reusable part - -

C458281C02
0.125,1.042 0.938,1.969 0.813,0.927 1.104,0.906 1.917,1.833 0.813,0.927 4.958,4.219 4.958,3.875 false 0.698,4.083 0.698,3.781 0.698,3.781 0.844,3.625 false 3.813,1.719 4.51,1.229 4.51,1.229 4.729,1.229 false 3.188,0.542 3.469,0.26 3.469,0.26 3.708,0.26 false 6.5,2.896 6.719,3.167 6.719,3.167 6.719,3.396 false 2.344,0.917 2.021,0.24 2.021,0.24 1.802,0.24 false 0.573,1.583 0.365,1.302 0.365,1.302 0.542,1.302 false 1.604,1.604 1.365,1.271 1.365,1.271 1.542,1.271 false 5.833,4.229 6.115,4.448 0.281,0.219 10 false x 4 6.625,1.677 6.906,1.896 0.281,0.219 10 false x 5 3.729,3.792 4.01,4.01 0.281,0.219 10 false x 3 6.583,3.438 6.969,3.75 0.385,0.313 18 false 27 4.813,4.229 5.167,4.573 0.354,0.344 18 false 25 4.781,1.094 5.198,1.438 0.417,0.344 18 false 29 0.563,4.104 1.417,4.427 0.854,0.323 18 false 30, 31 1.479,0.094 1.802,0.479 0.323,0.385 18 false 29 0.583,1.167 0.917,1.5 0.333,0.333 18 false 28 3.76,0.135 4.177,0.49 0.417,0.354 18 false 26 2.802,0.26 3.083,0.479 0.281,0.219 10 false x 2 1.573,1.135 1.906,1.469 0.333,0.333 18 false 28 0.156,1.063 0.406,1.292 0.25,0.229 10 false *A 1.135,0.938 1.385,1.167 0.25,0.229 10 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

25 REAR ENGINE MOUNTING INSULATOR 12371A - - -
26 EXHAUST PIPE SUPPORT BRACKET ASSEMBLY 17570 - - -
27 TRANSFER ASSEMBLY 36100 (Click here) - -
28 EXHAUST SENSOR CLAMP BRACKET - - - -
29 REMOVE WIRE HARNESS CLAMP BRACKET - - - -
30 REMOVE TORQUE CONVERTER ASSEMBLY 32000 (Click here) - -
31 INSPECT TORQUE CONVERTER ASSEMBLY 32000 (Click here) - -

*A for Type A *B for Type B

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Automatic transmission assembly ECU configuration - (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)

CAUTION:
·
C344337

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C13
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 37140 1.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (w/o Urea SCR System)

Hide 37110F 2.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 17420 3.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 17402 5.REMOVE NO. 2 FRONT EXHAUST PIPE SUB-ASSEMBLY

Hide 36336 8.REMOVE TRANSFER HEAT INSULATOR

Hide 36179 9.REMOVE LOWER TRANSFER CASE PROTECTOR

Hide 10.DRAIN TRANSFER OIL

Hide 12144 11.DISCONNECT OIL PAN COVER SILENCER

a.
C458298


Hide 32101A 12.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C458282N01
1.844,0.073 2.021,0.406 0.177,0.333 18 false i

i.

Remove the 6 drive plate and torque converter setting bolts from the drive plate and ring gear sub-assembly.

HINT:

Turn the crankshaft to a position where the drive plate and torque converter setting bolts can be removed, and remove the drive plate and torque converter setting bolts while securing the crankshaft pulley bolt with a wrench.




Hide 13.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY

a.
C458300


Hide 35979B 14.REMOVE TRANSMISSION INSULATOR RH

a.
C458283


Hide 33825 15.REMOVE TRANSMISSION CONTROL CABLE INSULATOR

Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

(Click here)

Hide 33823 17.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C453570


Hide 37140 18.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (w/ Urea SCR System)

Hide 19.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY

a.
C458284N01
1.99,0.063 2.208,0.396 0.219,0.333 18 false i

i.

Using a transmission jack and a belt sling, etc., support the automatic transmission assembly with transfer assembly.

NOTICE:

Using a belt sling, etc., secure the automatic transmission assembly with transfer assembly to the transmission jack to prevent it from falling.




Hide 20.REMOVE NO. 3 FRAME CROSSMEMBER ASSEMBLY (w/o Urea SCR System)

Hide 21.DISCONNECT WIRE HARNESS CLAMP BRACKET

Hide 36407 22.DISCONNECT TRANSFER BREATHER HOSE SUB-ASSEMBLY

Z101186

NOTICE:
·

The transfer breather hose sub-assembly can be disconnected without tilting the automatic transmission assembly with transfer assembly.

·
C462063

When tilting the automatic transmission with transfer assembly, disconnect the connector of the diesel throttle body assembly.

Do not tilt it excessively and allow the cooling fan and fan shroud to contact each other.




a.
C458285


Hide 23.DISCONNECT WIRE HARNESS

Z101186

NOTICE:
·

The wire harness can be disconnected without tilting the automatic transmission assembly with transfer assembly.

·
C462063

When tilting the automatic transmission with transfer assembly, disconnect the connector of the diesel throttle body assembly.

Do not tilt it excessively and allow the cooling fan and fan shroud to contact each other.




a.
C458286C01
6.188,1.802 6.427,1.802 false 0.49,1.698 0.646,1.698 0.646,1.698 0.781,1.917 true 0.479,0.094 1.219,0.448 0.74,0.354 18 false i - iii 0.354,1.625 0.552,1.844 0.198,0.219 10 true *a 6.021,1.729 6.229,1.927 0.208,0.198 10 false *b
*a Transmission Wire Connector *b TCM connector
V100135

Connector
V100136

Bolt
V113147

Pull Down the Lever
V113148

While Pressing the Lock
V113149

Pull Up the Lever - -


i.

Disconnect the 5 connectors.

NOTICE:
·

Disconnect the claw, pull down the lever, and then disconnect the transmission wire connector.

·

Disconnect the TCM connector lever while pressing the lever lock as shown in the illustration.




ii.

Detach the clamp.


iii.

Remove the 4 bolts and disconnect the wire harness from the automatic transmission assembly with transfer assembly.



Hide 24.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY

Z101186

NOTICE:
·

The automatic transmission assembly with transfer assembly can be removed without being tilted.

·
C462063

When tilting the automatic transmission with transfer assembly, disconnect the connector of the diesel throttle body assembly.

Do not tilt it excessively and allow the cooling fan and fan shroud to contact each other.




a.
C458287N01
0.177,0.042 0.354,0.375 0.177,0.333 18 false i 4.115,0.073 4.292,0.406 0.177,0.333 18 false ii

i.

Using an engine lifter and jack, support the engine.


ii.

Remove the 10 bolts and automatic transmission assembly with transfer assembly.

NOTICE:
·

Do not use excessive force to pry out the automatic transmission assembly with transfer assembly when separating it from the engine assembly to prevent the knock pins from being damaged.

·

When removing the automatic transmission assembly with transfer assembly, make sure that the oil cooler tube does not become damaged.





Hide 12371A 25.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 17570 26.REMOVE EXHAUST PIPE SUPPORT BRACKET ASSEMBLY

a.
C458302


Hide 36100 27.REMOVE TRANSFER ASSEMBLY

a.
C458288N01
2.094,0.063 2.375,0.417 0.281,0.354 18 false i

i.

Remove the 8 bolts and transfer assembly from the automatic transmission assembly.

NOTICE:
·

Check the center of gravity while removing the transfer assembly.

·

Do not drop the transfer assembly.





Hide 28.REMOVE EXHAUST SENSOR CLAMP BRACKET

a.
C466763C01
0.51,0.021 0.781,0.219 0.271,0.198 10 true *A 3.885,0.021 4.156,0.219 0.271,0.198 10 true *B
*A for Type A *B for Type B



Hide 29.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C453571


Hide 32000 30.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C458289C01
4.115,0.833 4.948,1.406 4.948,1.406 4.323,0.823 true 2.573,0.094 3.01,0.417 0.438,0.323 18 false i, ii 4.979,1.344 5.26,1.594 0.281,0.25 10 false *a
*a Matchmark - -


i.

Put matchmarks on the automatic transmission assembly with transfer assembly and torque converter assembly.


ii.

Remove the torque converter assembly from the automatic transmission assembly with transfer.



Hide 32000 31.INSPECT TORQUE CONVERTER ASSEMBLY

Z101186

Click here(Click here)