Home › Power Source / Network › F33A-FTV (BATTERY / CHARGING) › BATTERY CURRENT SENSOR › from 2021.07
RM38G0E _57 Power Source / Network _106328 F33A-FTV BATTERY / CHARGING _0489037 BATTERY CURRENT SENSOR A

F33A-FTV BATTERY / CHARGING  BATTERY CURRENT SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

A484890N01
6.688,0.219 6.854,0.219 false 1.094,0.573 1.344,0.573 false 1.25,1.542 1.667,1.542 false 1.354,1.917 1.625,1.917 false 1,0.917 1.167,0.917 1.167,0.917 1.333,0.948 false 1.875,1.188 2.083,1 2.083,1 2.167,1 false 6.51,0.115 6.792,0.469 0.281,0.354 18 false 1 0.896,0.469 1.177,0.823 0.281,0.354 18 false 2 1.021,1.417 1.302,1.771 0.281,0.354 18 false 3 1.125,1.833 1.438,2.031 0.313,0.198 10 false *1 2.229,0.917 2.542,1.115 0.313,0.198 10 false *2 0.823,0.854 1.135,1.052 0.313,0.198 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ENGINE SIDE COVER RH 51473C - - -
3 BATTERY STATE SENSOR ASSEMBLY 28850C - - -

*1 BATTERY CURRENT SENSOR HOLDER *2 GROUND WIRE
*3 ENGINE ROOM MAIN WIRE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the battery state sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 51473C 2.REMOVE ENGINE SIDE COVER RH

Hide 28850C 3.REMOVE BATTERY STATE SENSOR ASSEMBLY

A484892