Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRILLE SHUTTER SYSTEM › from 2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0469188 GRILLE SHUTTER SYSTEM J

EXTERIOR PANELS / TRIM  GRILLE SHUTTER SYSTEM  Grille Shutter does not Operate  


DESCRIPTION

The grille shutter of the radiator shutter sub-assembly may not operate when dirty due to foreign matter, snow, mud, etc., or the power supply voltage deteriorates.

WIRING DIAGRAM

E465521E01
1.021,0.573 2.823,0.906 1.802,0.333 10 false from EFI MAIN NO.3 Relay 3.104,0.771 4.292,0.99 1.188,0.219 10 false GRILLE SHUTT 4.167,1.99 6.25,2.26 2.083,0.271 10 false Radiator Shutter Assembly 4.354,1.188 4.635,1.563 0.281,0.375 10 false 1 4.354,0.448 4.635,0.823 0.281,0.375 10 false 3 4.625,0.615 5.083,1.021 0.458,0.406 10 false +B 4.646,1.313 5.448,1.76 0.802,0.448 10 false GND 4.188,1.833 4.646,2.031 0.458,0.198 10 false B21

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, change the grille shutter control mode to maintenance mode.

for V35A-FTS:

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

for F33A-FTV (w/o DPF):

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION

·

If the radiator shutter assembly has been replaced with a new one, perform initialization and change the grille shutter control mode.

for V35A-FTS:

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

for F33A-FTV (w/o DPF):

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.CHECK FOR GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

The radiator shutter sub-assembly is free of foreign matter and ice.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIATOR SHUTTER ASSEMBLY

NG

8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.CHECK RADIATOR SHUTTER ASSEMBLY
a.

Remove the radiator shutter assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

While using fingers to pinch the fin at the location shown in the illustration, fully open and close the radiator shutter assembly manually and check that it moves smoothly.

HINT:

If the fin is pinched with fingers far from the swing grille actuator assembly, the function may not be able to be inspected correctly.


B613103C01
1.167,1.135 1.323,1.135 1.323,1.135 1.552,0.865 true 3.344,2.458 3.458,2.458 3.458,2.458 3.865,1.823 true 3.125,2.375 3.438,2.531 0.313,0.156 10 false *a 0.979,1.063 1.292,1.219 0.313,0.156 10 false *b
*a Swing Grille Actuator *b Fin


OK:

The radiator shutter assembly moves smoothly.



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPLACE RADIATOR SHUTTER ASSEMBLY

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Result Proceed to
OK A
NG (for V35A-FTS) B
NG (for F33A-FTV [w/o DPF]) C



A

6.CHECK HARNESS AND CONNECTOR (RADIATOR SHUTTER ASSEMBLY - BATTERY)

B

C

6.CHECK HARNESS AND CONNECTOR (RADIATOR SHUTTER ASSEMBLY - BATTERY)
a.

Disconnect the B21 radiator shutter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B21)Location & Routing

Click Connector(B21)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Radiator Shutter Assembly

B21-3 (+B) - B21-1 (GND) Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B21)Location & Routing

Click Connector(B21)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Radiator Shutter Assembly

B21-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Grille Shutter Control Mode Grille shutter control mode status Normal or Maintenance Normal: Normal mode
Maintenance: Maintenance mode
-
Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
OK:

Normal is displayed.



Result:
Proceed to
NEXT



NEXT

END
HINT:

Operation temporarily abnormal due to fail-safe (abnormal temperature).



8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)