Home › Suspension › SUSPENSION CONTROL › STABILIZER CONTROL ECU › from 2021.07
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0472700 STABILIZER CONTROL ECU A

SUSPENSION CONTROL  STABILIZER CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C458587N01
5.75,1.813 5.75,1.313 5.75,1.313 6,1.313 false 2.646,3.917 2.646,4.167 2.646,4.167 3.146,4.167 false 6.5,0.25 6.833,0.25 false 6.5,0.667 6.833,0.667 false 6.313,0.125 6.563,0.458 0.25,0.333 18 false 1 6.313,0.542 6.563,0.875 0.25,0.333 18 false 3 6.052,1.188 6.302,1.521 0.25,0.333 18 false 2 3.479,4.042 3.729,4.375 0.25,0.333 18 false 4 2.125,3.958 2.458,4.208 0.333,0.25 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 QUARTER TRIM PANEL ASSEMBLY RH 62510M - - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 STABILIZER CONTROL ECU 89271A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the stabilizer control ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane tracing assist system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 62510M 2.REMOVE QUARTER TRIM PANEL ASSEMBLY RH

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 89271A 4.REMOVE STABILIZER CONTROL ECU

Z101186

NOTICE:
·

Avoid any impact to the stabilizer control ECU.

·

Do not drop the stabilizer control ECU. If it is dropped, replace it with a new one.




a.
C458588