Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Push Start Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E449356E02
1.156,1.99 1.771,2.188 0.615,0.198 10 false I75 1.167,2.156 3.771,2.354 2.604,0.198 10 false Engine Switch 3.302,0.688 3.917,0.885 0.615,0.198 10 false SWIL 5.115,0.698 5.729,0.896 0.615,0.198 10 false SWIL 6.167,0.781 6.479,0.979 0.313,0.198 10 false +B 4.969,2.135 6.552,2.531 1.583,0.396 10 false Certification ECU (Smart Key ECU Assembly) 4.969,1.969 5.583,2.167 0.615,0.198 10 false I39 5.135,1.313 5.75,1.51 0.615,0.198 10 false AGND 4.781,0.688 5.094,0.885 0.313,0.198 10 false 20 3.76,0.688 4.073,0.885 0.313,0.198 10 false 5 3.313,1.302 3.927,1.5 0.615,0.198 10 false GND 3.75,1.302 4.063,1.5 0.313,0.198 10 false 3 4.781,1.313 5.094,1.51 0.313,0.198 10 false 30

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the "Start Indicator Function" customization setting is set to "ON".

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly) or engine switch, refer to Service Bulletin.

·

When replacing the engine switch, always replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Start SW Light Power Supply Engine switch illumination OFF or ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Start SW Light Power Supply
50004 440 1
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH

Result:
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for V35A-FTS) C
NG (for F33A-FTV) D



A

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

B

C

D

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the I75 engine switch connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I75,I39)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I75-5 (SWIL) - I39-20 (SWIL) Always Below 1 Ω
I75-3 (GND) - I39-30 (AGND) Always Below 1 Ω
I75-5 (SWIL) or I39-20 (SWIL) - Body ground Always 10 kΩ or higher
I75-3 (GND) or I39-30 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR