If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Active Noise Control System | A |
| w/o Active Noise Control System | B |
A
B
Disconnect the I16 radio and display receiver assembly connector.
Disconnect the S25 stereo component equalizer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I16,S25)Location & Routingewd_type=routing;type=c,c;code=I16,S25 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=8,23,9,24 |
||
| I16-1 (FR+) - S25-8 (FRI+) | Always | Below 1 Ω |
| I16-6 (FR-) - S25-23 (FRI-) | Always | Below 1 Ω |
| I16-2 (FL+) - S25-9 (FLI+) | Always | Below 1 Ω |
| I16-7 (FL-) - S25-24 (FLI-) | Always | Below 1 Ω |
| I16-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I16-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| I16-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I16-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
B
Disconnect the I16 radio and display receiver assembly connector.
Disconnect the M9 and N7 front No. 1 speaker assembly connectors.
Disconnect the J1 and L3 front No. 3 speaker assembly connectors.
Disconnect the I56 telephone transceiver assembly connectors.*
*: w/ Telematics Transceiver (for Toyota Connected Services)
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Telematics Transceiver (for Toyota Connected Services) *2: w/ Telematics Transceiver (for Toyota Connected Services) |
||
Click Location & Routing(I16,J1,L3,I56,M9,N7)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=I16,J1,L3,I56,M9,N7 Click Connector(J1)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J1;pinno=4,2,3,1 Click Connector(L3)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L3;pinno=4,2,3,1 Click Connector(M9)Body>Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=M9;pinno=2,1 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 |
||
| I16-1 (FR+) - J1-4 (+) | Always | Below 1 Ω |
| I16-6 (FR-) - J1-2 (-) | Always | Below 1 Ω |
| I16-2 (FL+) - L3-4 (+)*1 | Always | Below 1 Ω |
| I16-7 (FL-) - L3-2 (-)*1 | Always | Below 1 Ω |
| I16-2 (FL+) - I56-1 (SPI+)*2 | Always | Below 1 Ω |
| I16-7 (FL-) - I56-2 (SPI-)*2 | Always | Below 1 Ω |
| I56-3 (SPO+) - L3-4 (+)*2 | Always | Below 1 Ω |
| I56-4 (SPO-) - L3-2 (-)*2 | Always | Below 1 Ω |
| J1-3 (TWR+) - M9-2 (+) | Always | Below 1 Ω |
| J1-1 (TWR-) - M9-1 (-) | Always | Below 1 Ω |
| L3-3 (TWL+) - N7-2 (+) | Always | Below 1 Ω |
| L3-1 (TWL-) - N7-1 (-) | Always | Below 1 Ω |
| I16-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I16-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| I16-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I16-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| J1-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| J1-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L3-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Telematics Transceiver (for Toyota Connected Services) | A |
| w/o Telematics Transceiver (for Toyota Connected Services) | B |
A
B
| *a | Component without harness connected (Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SPO+) - 1 (SPI+) | Always | Below 1 Ω |
| 4 (SPO-) - 2 (SPI-) | Always | Below 1 Ω |
| 1 (SPI+) - 2 (SPI-) | Always | 10 kΩ or higher |
| 3 (SPO+) - 4 (SPO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I16 radio and display receiver assembly connector.
Disconnect the O9 and P9 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I16,O9,P9)Location & Routingewd_type=routing;type=c,c,c;code=I16,O9,P9 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| I16-4 (RR+) - O9-2 (+) | Always | Below 1 Ω |
| I16-9 (RR-) - O9-1 (-) | Always | Below 1 Ω |
| I16-3 (RL+) - P9-2 (+) | Always | Below 1 Ω |
| I16-8 (RL-) - P9-1 (-) | Always | Below 1 Ω |
| I16-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| I16-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| I16-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| I16-8 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG