| *A | for GR SPORT | *B | except GR SPORT |
| *C | for Standard | *D | for Full Cover Type |
| ● | Non-reusable part | - | - |
Use the same procedure for the RH and LH sides.
The procedure described below is for the LH side.
75606B 1.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH
|
Place Hand Here |
|
Remove in this Direction |
|
Screw |
|
Clip |
Put protective tape around the quarter outside moulding sub-assembly LH.
Using a 4 mm hexagon socket wrench, remove the screw.
Remove the 2 clips.
Place your hand at the positions shown in the illustration and detach the clip in the order shown in the illustration.
Using moulding remover B, detach the clip in the order shown in the illustration and remove the quarter outside moulding sub-assembly LH as shown in the illustration.
Detach the clip one by one.
75078 2.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH (for GR SPORT)
|
Remove in this Direction |
|
Screw |
|
Clip | - | - |
Put protective tape around the rear door lower outside moulding sub-assembly LH.
Using a 4 mm hexagon socket wrench, remove the screw.
Remove the 3 clips.
Using moulding remover B, detach the clip in the order shown in the illustration and remove the rear door lower outside moulding sub-assembly LH as shown in the illustration.
Detach the clip one by one.
75078 3.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH (except GR SPORT)
|
|
| Part | Temperature |
|---|---|
| Rear Door Lower Outside Moulding Sub-assembly LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door lower outside moulding sub-assembly LH excessively.
| *a | Double-sided Tape | - | - |
|
Remove in this Direction |
|
Screw |
|
Clip | - | - |
Put protective tape around the rear door lower outside moulding sub-assembly LH.
Using a 4 mm hexagon socket wrench, remove the screw.
Remove the 3 clips.
Heat the adhesive of the rear door lower outside moulding sub-assembly LH using a heat light.
Using moulding remover B, detach the clip and double-sided tape in the order shown in the illustration and remove the rear door lower outside moulding sub-assembly LH as shown in the illustration.
Detach the clip one by one.
4.REMOVE REAR DOOR NO. 1 MOULDING PAD (except GR SPORT)
|
|
| Part | Temperature |
|---|---|
| Rear Door No. 1 Moulding Pad | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door No. 1 moulding pad excessively.
Heat the adhesive of the rear door No. 1 moulding pad using a heat light.
Remove the rear door No. 1 moulding pad.
75860A 5.REMOVE BODY ROCKER PANEL MOULDING ASSEMBLY LH (for Standard)
51774C 6.REMOVE STEP PLATE COVER LH (for Full Cover Type)
75874 7.REMOVE QUARTER PANEL WHEEL OPENING MOULDING LH
|
|
| Part | Temperature |
|---|---|
| Quarter Panel Wheel Opening Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the quarter panel wheel opening moulding LH.
| *a | Double-sided Tape | - | - |
|
Remove in this Direction |
|
Screw |
|
Grommet | - | - |
Using a clip remover with its tip wrapped with protective tape, detach the clip.
Remove the screw.
Push on the rear wheel house liner LH and use needle-nose pliers from the backside to remove the grommet.
Heat the adhesive of the quarter panel wheel opening moulding LH using a heat light.
Detach the double-sided tape and remove the quarter panel wheel opening moulding LH as shown in the illustration.