Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD) › from 2021.07
RM38G0E _54 Brake _100464 BRAKE SYSTEM (OTHER) _0467266 BRAKE PEDAL(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C452254N05
2.052,2 2.219,2 2.219,2 2.469,1.333 false 1.833,1.865 2.115,2.219 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L - - -

C458918N01
2.125,0.458 2.292,0.458 2.292,0.458 2.875,0.792 false 1.865,0.271 2.146,0.625 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

2 AIR DUCT SUB-ASSEMBLY - - - -

C452211N08
5.052,3.083 5.51,3.677 5.51,3.677 5.677,3.677 false 3.615,2.281 3.969,1.823 3.969,1.823 4.052,1.823 false 4.854,1.333 5.208,0.875 5.208,0.875 5.292,0.875 false 1.26,3.896 1.344,3.896 1.344,3.896 1.76,3.438 false 4.208,5.219 4.677,4.781 4.677,4.781 4.76,4.781 false 0.25,3.448 0.25,3.031 false 5.719,3.531 6.208,4.135 0.49,0.604 18 true 3 4.125,1.646 4.615,2.25 0.49,0.604 18 false 4 5.354,0.729 5.844,1.333 0.49,0.604 18 false 5 1.01,3.729 1.5,4.333 0.49,0.604 18 false 6 4.844,4.625 5.333,5.229 0.49,0.604 18 false 7 5.448,2.479 5.938,3.083 0.49,0.604 10 false x 2 0.375,2.948 0.865,3.552 0.49,0.604 10 false x 2 0.208,3.469 0.698,4.073 0.49,0.604 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

3 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D - - -
4 STOP LIGHT SWITCH MOUNTING ADJUSTER 84345 - - -
5 ENGINE ROOM MAIN WIRE 82111 - - -
6 BRAKE PEDAL SUPPORT ASSEMBLY 47110 - - -
7 BRAKE PEDAL PAD 47121 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Brake pedal support assembly* Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system does not operate correctly


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 47210L 1.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Hide 2.REMOVE AIR DUCT SUB-ASSEMBLY

Hide 89510D 3.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

Hide 84345 4.REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

Hide 82111 5.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C452217


Hide 47110 6.DISCONNECT BRAKE PEDAL SUPPORT ASSEMBLY

a.
C452219


Hide 47121 7.REMOVE BRAKE PEDAL PAD

a.
C455278