| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( ) |
- | - |
| 2 | ENGINE SIDE COVER RH | 51473C | - | - | - |
| 3 | PERFORM ACCUMULATOR PRESSURE ZERO DOWN | - | ( ) |
- | - |
| 4 | DRAIN BRAKE FLUID | - | - | ( ) |
- |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY | 73900 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | BRAKE PEDAL RETURN SPRING | 47101A | - | - | - |
| 7 | STOP LIGHT SWITCH ASSEMBLY | 84340 | - | - | - |
| ● | Non-reusable part |
|
Lithium soap base glycol grease |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | NO. 1 RESERVOIR HOSE | - | ( ) |
- | - |
| 18 | NO. 2 RESERVOIR HOSE | - | ( ) |
- | - |
| 19 | NO. 1 WIRE CLAMP BRACKET | - | ( ) |
- | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
| *a | No. 1 Skid Control ECU |
| *b | No. 1 Reservoir Hose and No. 2 Reservoir Hose |
| *c | Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Brake Master Cylinder Reservoir |
| *f | No. 1 Brake Actuator Tube |
| *g | No. 1 Wire Clamp Bracket |
| *h | Brake Booster Pump with Accumulator Assembly |
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
1. PRECAUTION
51473C 2.REMOVE ENGINE SIDE COVER RH
4.DRAIN BRAKE FLUID
|
|
73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
47101A 6.REMOVE BRAKE PEDAL RETURN SPRING
84340 7.REMOVE STOP LIGHT SWITCH ASSEMBLY
47264A 8.REMOVE PUSH ROD PIN
82111 9.DISCONNECT ENGINE ROOM MAIN WIRE
|
Release the lock lever |
|
Disconnect the connector |
Disconnect the brake fluid level warning switch connector.
Be careful not to allow any brake fluid to enter the connector.
Disengage the clamp to disconnect the engine room main wire from the brake booster with master cylinder assembly.
Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
Be careful not to allow any brake fluid to enter the connector.
10.REMOVE BRAKE TUBE
Using a union nut wrench, remove the 2 tubes from the brake actuator assembly and brake booster with master cylinder assembly..
Do not kink or damage the brake tubes.
Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.
Disengage the 2 clamps and remove the 2 brake tubes from the No. 2 brake tube clamp.
Do not kink or damage the brake tubes.
47210L 12.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Disconnect the connector.
Remove the nut and siren.
Remove the 4 nuts and brake booster with master cylinder assembly.
Do not apply excessive force to the brake lines.
Be careful not to allow any brake fluid to enter the connector.
| *a | No. 1 Skid Control ECU |
| *b | No. 1 Reservoir Hose and No. 2 Reservoir Hose |
| *c | Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Brake Master Cylinder Reservoir |
| *f | No. 1 Brake Actuator Tube |
| *g | No. 1 Wire Clamp Bracket |
| *h | Brake Booster Pump with Accumulator Assembly |
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
44785D 13.REMOVE BRAKE MASTER CYLINDER GASKET
14.REMOVE BOOSTER BRACKET STOPPER RING
15.REMOVE BRAKE BOOSTER BRACKET
44785D 16.REMOVE BRAKE MASTER CYLINDER GASKET
17.REMOVE NO. 1 RESERVOIR HOSE
|
|
18.REMOVE NO. 2 RESERVOIR HOSE
|
|
19.REMOVE NO. 1 WIRE CLAMP BRACKET
|
|
Using a 5 mm long hexagon socket wrench, remove the bolt and No. 1 wire clamp bracket.