Home › Engine / Hybrid System › F33A-FTV (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › from 2021.07
RM38G0E _51 Engine / Hybrid System _106330 F33A-FTV ENGINE MECHANICAL _0491797 FRONT CRANKSHAFT OIL SEAL A

F33A-FTV ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A493545N02
1.708,1.99 2.156,1.313 2.156,1.313 2.354,1.313 true 3.188,2.01 3.417,2.01 3.417,2.01 3.833,2.844 true 4.271,1.802 4.5,1.802 4.5,1.802 4.667,2.823 true 5.292,4.51 6.01,4.51 true 3.375,4.646 3.375,5.104 true 2.417,1.177 2.698,1.531 0.281,0.354 18 false 1 2.99,1.885 3.271,2.24 0.281,0.354 18 false 2 4.073,1.688 4.354,2.042 0.281,0.354 18 false 5 3.885,1.729 4.167,2.083 0.281,0.354 10 false ● 3.177,3.24 3.594,3.583 0.417,0.344 10 false x 3 3.323,5.125 3.604,5.479 0.281,0.354 18 false 3 6.073,4.375 6.354,4.729 0.281,0.354 18 false 4 2.729,4.792 3.125,5.219 0.396,0.427 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RADIATOR ASSEMBLY 16400 - - -
2 CRANKSHAFT PULLEY SUB-ASSEMBLY 13408 (Click here) - -
3 V-RIBBED BELT TENSIONER ASSEMBLY 16620D - - -
4 NO. 2 TIMING CHAIN COVER INSULATOR 11339D - - -
5 TIMING CHAIN OR BELT COVER OIL SEAL 11302A (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 13408 2.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY

a.
A536641C02
4.948,1.271 4.948,1.479 4.948,1.479 5.094,1.479 true 1.698,0.938 1.792,1.042 1.792,1.042 1.917,1.042 true 1.396,0.052 2.021,0.313 0.625,0.26 18 true i, ii, iii 1.938,0.958 2.115,1.125 0.177,0.167 10 true *a 5.104,1.417 5.292,1.563 0.188,0.146 10 true *b
*a Service Hole *b Protrusion


i.

Align the service hole of the crankshaft pulley sub-assembly with the position as shown in the illustration.


ii.

Install a service bolt and fix the crankshaft pulley sub-assembly.

Service Bolt
Length 120 mm (4.72 in.) or more
Diameter 14 mm (0.551 in.)
Pitch 1.5
Thread Length 70 mm (2.76 in.) or more

HINT:

The crankshaft pulley sub-assembly is fixed by hooking a service bolt on the convex part of the timing chain cover sub-assembly.



iii.

Remove the 3 bolts and crankshaft pulley sub-assembly.

NOTICE:

If the crankshaft pulley sub-assembly cannot be removed, temporarily install a bolt to the crankshaft so that the pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the pulley.




Hide 16620D 3.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11339D 4.REMOVE NO. 2 TIMING CHAIN COVER INSULATOR

Hide 11302A 5.REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

a.
A493544C01
3.219,0.802 3.448,0.323 3.448,0.323 3.604,0.323 true 3.635,0.25 3.813,0.396 0.177,0.146 10 true *a 5.302,0.458 5.563,0.646 0.26,0.188 10 false *b 1.417,0.063 1.802,0.344 0.385,0.281 18 true i, ii
*a Protective Tape *b Cut Position


i.

Using a knife, cut off the lip of the timing chain or belt cover oil seal.


ii.

Using a screwdriver with its tip taped, pry out the timing chain or belt cover oil seal.

NOTICE:

After the removal, check the crankshaft for damage.