| *1 | FLUID COUPLING ASSEMBLY WITH FAN | *2 | FAN PULLEY |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | NO. 2 INTERCOOLER COOLING RADIATOR ASSEMBLY | 16550B | - | - | - |
| 18 | NO. 1 RADIATOR TO SUPPORT SEAL | 16561C | - | - | - |
| 19 | CONNECTOR COVER | 82H21F | - | - | - |
| 20 | ELECTRIC WATER PUMP ASSEMBLY | 161B0 | - | - | - |
| 21 | NO. 1 WATER BY-PASS PIPE | 16268 | - | - | - |
| 22 | WATER HOSE JOINT | 16035 | - | - | - |
| 23 | FRONT WATER BY-PASS JOINT SUB-ASSEMBLY | 16035B | - | - | - |
| 24 | NO. 1 RADIATOR BRACKET | 16582 | - | - | - |
| 25 | NO. 9 WATER BY-PASS HOSE | 16297 | - | - | - |
| 26 | NO. 8 WATER BY-PASS HOSE | 16296 | - | - | - |
| 27 | DISCONNECT FRONT RADIATOR SIDE AIR GUIDE PLATE LH | 16695A | - | - | - |
| 28 | NO. 2 RADIATOR BRACKET | 16583 | - | - | - |
| 29 | REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH | 16695A | - | - | - |
| 30 | FRONT RADIATOR SIDE AIR GUIDE PLATE RH | 16691A | - | - | - |
| *A | w/o Condenser Fan | *B | w/ Condenser Fan |
| *1 | ENGINE ROOM MAIN WIRE | - | - |
| ● | Non-reusable part | - | - |
| *A | w/ Condenser Fan | - | - |
| *1 | RADIATOR ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the radiator assembly removal/installation are shown below.
12601B 1.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
2.REMOVE FRONT BUMPER ASSEMBLY
for Standard
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>REMOVAL
for Aero Type
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Aero Type)>REMOVAL
51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
4.DRAIN ENGINE COOLANT
5.DRAIN ENGINE COOLANT (for Intercooler)
6.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
16361A 7.REMOVE FAN AND GENERATOR V BELT
16261 8.DISCONNECT WATER BY-PASS HOSE
16267 9.DISCONNECT NO. 3 WATER BY-PASS HOSE
164A2 10.REMOVE RADIATOR RESERVE TANK ASSEMBLY
16264D 11.REMOVE NO. 2 WATER BY-PASS HOSE
16571C 12.REMOVE NO. 1 RADIATOR HOSE
16572D 13.REMOVE NO. 2 RADIATOR HOSE
16278 14.DISCONNECT NO. 2 WATER BY-PASS PIPE
15.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY
16711 16.REMOVE FAN SHROUD
Loosen the 4 nuts holding the fluid coupling assembly with fan.
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts.
Remove the fan shroud together with the fluid coupling assembly with fan.
Be careful not to damage the radiator core.
Remove the fan pulley from the fan bracket sub-assembly.
16550B 17.REMOVE NO. 2 INTERCOOLER COOLING RADIATOR ASSEMBLY
16561C 18.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
82H21F 19.REMOVE CONNECTOR COVER
161B0 20.DISCONNECT ELECTRIC WATER PUMP ASSEMBLY
16268 21.DISCONNECT NO. 1 WATER BY-PASS PIPE
16035 22.DISCONNECT WATER HOSE JOINT
16035B 23.DISCONNECT FRONT WATER BY-PASS JOINT SUB-ASSEMBLY
16582 24.REMOVE NO. 1 RADIATOR BRACKET
16297 25.DISCONNECT NO. 9 WATER BY-PASS HOSE
16296 26.DISCONNECT NO. 8 WATER BY-PASS HOSE
16695A 27.DISCONNECT FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16583 28.REMOVE NO. 2 RADIATOR BRACKET
16695A 29.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16691A 30.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH
44402 31.DISCONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY
88710E 32.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Remove the bolt and disconnect the air conditioning tube and accessory assembly.
Remove the O-ring from the air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
88711 33.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
34.REMOVE RADIATOR WITH COOLER CONDENSER ASSEMBLY
w/ Condenser Fan:
|
Remove in this Direction | - | - |
Detach the clamp and disconnect the connector.
Remove the 6 bolts.
Remove the radiator with cooler condenser assembly from the vehicle as shown in the illustration.
Perform the following procedure with 2 or more people to prevent damage to the radiator with cooler condenser assembly.
When removing the radiator with cooler condenser assembly from the vehicle, do not apply excessive force to the cooler pipe or cooling hoses.
w/o Condenser Fan:
|
Remove in this Direction | - | - |
Remove the 6 bolts.
Remove the radiator with cooler condenser assembly from the vehicle as shown in the illustration.
Perform the following procedure with 2 or more people to prevent damage to the radiator with cooler condenser assembly.
When removing the radiator with cooler condenser assembly from the vehicle, do not apply excessive force to the cooler pipe or cooling hoses.
88590 35.REMOVE BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
37.REMOVE COOLER BRACKET
16681 39.REMOVE UPPER RADIATOR AIR GUIDE PLATE
16561 40.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL