Home › Power Source / Network › F33A-FTV (BATTERY / CHARGING) › GENERATOR (for VALEO Made) › from 2021.07
RM38G0E _57 Power Source / Network _106328 F33A-FTV BATTERY / CHARGING _0489035 GENERATOR(for VALEO Made) A

F33A-FTV BATTERY / CHARGING  GENERATOR(for VALEO Made)  REMOVAL  


CAUTION / NOTICE / HINT

A488353N03
4.281,3.26 4.448,3.26 false 6.635,0.531 6.885,0.531 false 6.583,0.229 6.833,0.229 false 0.219,2.031 0.469,2.031 false 2.75,1.583 3.083,1.583 false 2.01,0.615 2.094,0.615 2.094,0.615 2.344,0.781 false 2.521,2.917 2.615,3.271 2.615,3.271 2.76,3.271 false 6.448,0.417 6.729,0.771 0.281,0.354 18 false 1 6.417,0.104 6.698,0.458 0.281,0.354 18 false 2 0.052,1.906 0.333,2.26 0.281,0.354 18 false 3 3.177,1.448 3.458,1.802 0.281,0.354 18 false 4 1.813,0.479 2.094,0.833 0.281,0.354 18 false 5 4.865,3.125 5.146,3.479 0.281,0.354 18 false 6 2.813,3.188 3.125,3.385 0.313,0.198 10 false *1 3.583,2.688 3.896,2.885 0.313,0.198 10 false x 2 3.01,0.552 3.323,0.75 0.313,0.198 10 false x 2 3.115,2.448 3.427,2.646 0.313,0.198 10 false x 2 3.542,3.156 3.854,3.354 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 RADIATOR WITH COOLER CONDENSER ASSEMBLY - - - -
4 ENGINE WIRE 82121 - - -
5 IDLER PULLEY SUB-ASSEMBLY 16603B - - -
6 GENERATOR ASSEMBLY 27060 (Click here) - -

*1 OIL COOLER TUBE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures(adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the generator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE RADIATOR WITH COOLER CONDENSER ASSEMBLY

Hide 82121 4.DISCONNECT ENGINE WIRE

a.
A488311


Hide 16603B 5.REMOVE IDLER PULLEY SUB-ASSEMBLY

a.
A488312


Hide 27060 6.REMOVE GENERATOR ASSEMBLY

a.
A488313N01
0.26,0.021 0.396,0.292 0.135,0.271 18 true i 2.615,0.073 2.76,0.344 0.146,0.271 18 true ii 5.219,0.042 5.427,0.292 0.208,0.25 18 true iii

i.

Remove the bolt and disconnect the oil cooler tube sub-assembly from the generator assembly.


ii.

Remove the 2 bolts and 2 nuts.


iii.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and generator assembly.