Home › Engine / Hybrid System › F33A-FTV (FUEL) › FUEL TANK › from 2021.07
RM38G0E _51 Engine / Hybrid System _106331 F33A-FTV FUEL _0492007 FUEL TANK A

F33A-FTV FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A492458N02
6.365,0.26 6.823,0.26 false 6.365,0.667 6.781,0.667 false 4.76,3.031 5.448,3.125 5.448,3.125 5.698,3.125 false 3.667,1 4.333,1 false 1.417,0.292 1.583,0.292 1.583,0.292 2,0.625 false 0.688,1.74 1.104,1.74 false 2.917,2.521 3.083,2.521 3.083,2.521 3.417,2.354 false 5.781,3.521 6.198,3.469 6.198,3.469 6.396,3.469 false 5.281,6 5.531,6.333 5.531,6.333 5.698,6.333 false 4.281,4.49 4.656,4.917 4.656,4.917 4.823,4.917 false 1.698,2.833 1.396,2.552 1.396,2.552 1.229,2.552 false 1.615,3.896 2.156,3.896 false 0.854,4.26 1.021,4.26 1.021,4.26 1.229,4.479 false 0.938,5.573 1.271,5.573 false 2.438,5.135 2.604,5.135 2.604,5.135 2.771,5.385 false 4.542,3.885 4.406,3.885 4.406,3.885 4.094,3.333 true 5.417,2.552 5.677,2.073 5.677,2.073 5.823,2.073 false 5,3.469 5.438,3.771 5.438,3.771 5.604,3.771 false 1.979,5.875 2.229,6.208 2.229,6.208 2.396,6.208 false 3.302,5.594 3.719,5.76 3.719,5.76 3.885,5.76 false 3.854,1.719 4.146,1.885 0.292,0.167 10 false x 2 4.208,5.042 4.5,5.208 0.292,0.167 10 false x 5 0.5,4.75 0.792,4.917 0.292,0.167 10 false x 4 6.667,6.177 6.958,6.344 0.292,0.167 10 false x 5 6.208,0.094 6.375,0.354 0.167,0.26 18 false 1 6.198,0.51 6.417,0.781 0.219,0.271 18 false 2 1.229,0.146 1.448,0.417 0.219,0.271 18 false 3 0.521,1.594 0.74,1.865 0.219,0.271 18 false 4 6.458,3.323 6.677,3.594 0.219,0.271 18 false 5 4.375,0.844 4.594,1.115 0.219,0.271 18 false 6 5.75,6.188 5.969,6.458 0.219,0.271 18 false 7 4.823,3.781 5.042,4.052 0.219,0.271 18 false 8 5.74,2.948 6.51,3.24 0.771,0.292 18 false 9, 16 5.865,1.917 6.604,2.177 0.74,0.26 18 false 10, 15 0.49,2.427 1.25,2.719 0.76,0.292 18 false 11, 13 1.292,3.75 1.615,4.021 0.323,0.271 18 false 12 2.625,2.365 2.948,2.635 0.323,0.271 18 false 14 0.5,4.115 0.823,4.385 0.323,0.271 18 false 17 5.146,4.781 5.469,5.052 0.323,0.271 18 false 18 5.635,3.677 5.875,3.844 0.24,0.167 10 false *1 0.771,5.479 1.01,5.646 0.24,0.167 10 false *2 2.26,5.042 2.5,5.208 0.24,0.167 10 false *2 2.427,6.115 2.667,6.281 0.24,0.167 10 false *3 3.927,5.656 4.167,5.823 0.24,0.167 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 CENTER EXHAUST PIPE ASSEMBLY 17420 - - -
4 REAR PROPELLER SHAFT ASSEMBLY 37110F - - -
5 FUEL TANK CAP ASSEMBLY 77310A - - -
6 FUEL TANK VENT TUBE ASSEMBLY 77010 - - -
7 NO. 2 FUEL TANK PROTECTOR SUB-ASSEMBLY 77607C - - -
8 NO. 1 FUEL TANK BREATHER TUBE SUB-ASSEMBLY - (Click here) - -
9 DISCONNECT FUEL TANK TO FILLER PIPE HOSE 77213E - - -
10 DISCONNECT FUEL HOSE 77259C - - -
11 DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209C (Click here) - -
12 FUEL TANK SUB-ASSEMBLY 77001A (Click here) - -
13 REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209C - - -
14 NO. 2 FUEL TANK PROTECTOR 77642A - - -
15 REMOVE FUEL HOSE 77259C - - -
16 REMOVE FUEL TANK TO FILLER PIPE HOSE 77213E - - -
17 NO. 1 FUEL TANK HEAT INSULATOR 77697 (Click here) - -
18 NO. 2 FUEL TANK HEAT INSULATOR 77697A (Click here) - -

*1 FUEL TANK FILLER PIPE *2 PIN
*3 FUEL TANK BAND - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel sub tank sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.


·
A344817

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17420 3.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 37110F 4.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 77310A 5.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77607C 7.REMOVE NO. 2 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A482084


Hide 8.DISCONNECT NO. 1 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A482085N01
2.042,0.104 2.229,0.375 0.188,0.271 18 false i

i.

Disconnect the No. 1 fuel tank breather tube sub-assembly from the fuel tank filler pipe.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 77213E 9.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A482086


Hide 77259C 10.DISCONNECT FUEL HOSE

a.
A492467


Hide 77209C 11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A492459

i.

Disconnect the fuel tank main tube sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 77001A 12.REMOVE FUEL TANK SUB-ASSEMBLY

Z101186

CAUTION:

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.



a.
A482091N01
0.396,0.115 0.573,0.365 0.177,0.25 18 true i 3.865,0.104 4.042,0.354 0.177,0.25 18 true ii 2.115,1.99 2.354,2.24 0.24,0.25 18 true iii

i.

Using an engine lifter and attachments, support the fuel tank sub-assembly.


ii.

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


iii.

Slightly lower the engine lifter.



Hide 77209C 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A492460


Hide 77642A 14.REMOVE NO. 2 FUEL TANK PROTECTOR

a.
A482095


Hide 77259C 15.REMOVE FUEL HOSE

a.
A492468


Hide 77213E 16.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A492461


Hide 77697 17.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A482098N01
3.75,0.76 3.906,0.958 0.156,0.198 10 false 1 5.083,0.76 5.24,0.958 0.156,0.198 10 false 2 6.406,0.76 6.563,0.958 0.156,0.198 10 false 3 0.5,0.302 0.74,0.552 0.24,0.25 18 false i

i.

Using a needle nose pliers, detach the 4 clips and remove the No. 1 fuel tank heat insulator from the fuel tank sub-assembly.



Hide 77697A 18.REMOVE NO. 2 FUEL TANK HEAT INSULATOR

a.
A482099N01
3.583,0.75 3.74,0.948 0.156,0.198 10 false 1 4.938,0.75 5.094,0.948 0.156,0.198 10 false 2 6.281,0.75 6.438,0.948 0.156,0.198 10 false 3 0.49,0.313 0.729,0.563 0.24,0.25 18 false i

i.

Using a needle nose pliers, detach the 5 clips and remove the No. 2 fuel tank heat insulator from the fuel tank sub-assembly.