Home › Engine / Hybrid System › F33A-FTV (FUEL) › FUEL TEMPERATURE SENSOR › from 2021.07
RM38G0E _51 Engine / Hybrid System _106331 F33A-FTV FUEL _0492551 FUEL TEMPERATURE SENSOR A

F33A-FTV FUEL  FUEL TEMPERATURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487539N01
6.448,0.188 6.865,0.188 false 6.479,0.594 6.813,0.594 false 3.417,1.917 4.167,1.917 false 4.396,0.531 4.813,0.781 4.813,0.781 4.979,0.781 false 4.01,0.583 4.396,1.052 4.396,1.052 4.563,1.052 false 4.219,1.771 4.406,2.052 0.188,0.281 18 false 3 6.292,0.031 6.479,0.313 0.188,0.281 18 false 1 6.313,0.448 6.5,0.729 0.188,0.281 18 false 2 5.021,0.625 5.208,0.906 0.188,0.281 18 false 4 4.604,0.969 5.073,1.146 0.469,0.177 10 false ● *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 FUEL FILTER ASSEMBLY 23300 - - -
4 FUEL TEMPERATURE SENSOR 89454 - - -

*1 FUEL FILTER GASKET - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel temperature sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

Check the area around the fuel filter assembly for dirt and clean it if it is, before work.


PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 89454 4.REMOVE FUEL TEMPERATURE SENSOR

a.
A487538N01
2.438,0.104 2.594,0.375 0.156,0.271 18 false i

i.

Remove the fuel temperature sensor and fuel filter gasket.