Home › Steering › STEERING COLUMN › STEERING PAD SWITCH › from 2021.07
RM38G0E _55 Steering _100923 STEERING COLUMN _0469201 STEERING PAD SWITCH A

STEERING COLUMN  STEERING PAD SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C464528N02
4.146,1.729 5.385,2.635 1.24,0.906 4.708,2.385 4.625,2.385 4.625,2.385 4.5,2.042 true 6.26,1.938 6.094,1.938 6.094,1.938 6.01,1.688 true 4.333,0.75 4.083,0.75 4.083,0.75 3.917,1.083 true 4.979,2.302 5.292,2.5 0.313,0.198 10 false ● 6.333,1.781 6.729,2.115 0.396,0.333 18 false 1 5.125,2.25 5.521,2.583 0.396,0.333 18 false 2 4.198,1.771 4.573,2.01 0.375,0.24 12 false *A 4.417,0.604 4.813,0.938 0.396,0.333 18 false 3 4.99,1.219 5.302,1.417 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HORN BUTTON ASSEMBLY 45130 - - -
2 STEERING WHEEL MARK ORNAMENT 45124A (Click here) - -
3 STEERING PAD SWITCH ASSEMBLY 84250A - - -

*A for GR SPORT - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering pad switch assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45130 1.REMOVE HORN BUTTON ASSEMBLY

Hide 45124A 2.REMOVE STEERING WHEEL MARK ORNAMENT (for GR SPORT)

a.
C462852C02
0.469,0.083 1.177,0.448 0.708,0.365 18 false i - iii
V100155

Protective Tape - -


i.

Apply protective tape around the steering wheel mark ornament.


ii.

Using a screwdriver with its tip wrapped with protective tape, remove the steering mark wheel ornament.


iii.

Remove the protective tape.



Hide 84250A 3.REMOVE STEERING PAD SWITCH ASSEMBLY

a.
C456096