Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P004518  Turbocharger/Supercharger Boost Control "A" Circuit Current Below Threshold  P004519  Turbocharger/Supercharger Boost Control "A" Circuit Current Above Threshold  P004600  Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance  P12A000  Turbocharger/Supercharger Boost Control "C" Circuit Range/Performance  P12A018  Turbocharger/Supercharger Boost Control "C" Circuit Current Below Threshold  P12A019  Turbocharger/Supercharger Boost Control "C" Circuit Current Above Threshold  


DESCRIPTION

These DTCs indicate that the variable vane DC motor of the turbocharger is malfunctioning. The ECM monitors the variable vane DC motor current to detect an open or short in the variable vane DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The variable vane DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the variable vane DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (Variable vane DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (Variable vane DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P004518 Turbocharger/Supercharger Boost Control "A" Circuit Current Below Threshold The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more.
(1 trip detection logic)
·

Open in variable vane DC motor (turbocharger nozzle vane control actuator bank 1) circuit

·

Turbocharger nozzle vane control actuator bank 1

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P0047
P004519 Turbocharger/Supercharger Boost Control "A" Circuit Current Above Threshold Overcurrent is detected 25 times or more.
(1 trip detection logic)
·

Short in variable vane DC motor (turbocharger nozzle vane control actuator bank 1) circuit

·

Turbocharger nozzle vane control actuator bank 1

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P0048
P004600 Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic)
·

Turbocharger nozzle vane control actuator bank 1

·

No. 1 Turbocharger sub-assembly

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P0046
P12A000 Turbocharger/Supercharger Boost Control "C" Circuit Range/Performance The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic)
·

Turbocharger nozzle vane control actuator bank 2

·

No. 2 Turbocharger sub-assembly

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P12A1
P12A018 Turbocharger/Supercharger Boost Control "C" Circuit Current Below Threshold The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more.
(1 trip detection logic)
·

Open in variable vane DC motor (turbocharger nozzle vane control actuator bank 2) circuit

·

Turbocharger nozzle vane control actuator bank 2

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P12A2
P12A019 Turbocharger/Supercharger Boost Control "C" Circuit Current Above Threshold Overcurrent is detected 25 times or more.
(1 trip detection logic)
·

Short in variable vane DC motor (turbocharger nozzle vane control actuator bank 2) circuit

·

Turbocharger nozzle vane control actuator bank 2

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on SAE Code: P12A3

HINT:
·

If DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

-

Vehicle surge when driving with full load


·

If DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P004518
P004519
P004600
Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.
P12A000
P12A018
P12A019
Maintain the Active Test "Activate the VN Turbo 1 and 2 Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.

WIRING DIAGRAM

A492901E01
6.01,4.354 6.563,4.625 0.552,0.271 10 false ECM 0.542,1.708 1.156,1.906 0.615,0.198 10 false C159 0.542,1.896 5.021,2.344 4.479,0.448 10 false DC Motor (Turbocharger Nozzle Vane Control Actuator Bank 1) 0.49,4.083 1.104,4.281 0.615,0.198 10 false C163 6,4.177 6.615,4.375 0.615,0.198 10 false C138 1.781,0.385 2.094,0.583 0.313,0.198 10 false M+ 1.781,1.063 2.094,1.26 0.313,0.198 10 false M- 2.063,0.396 2.219,0.594 0.156,0.198 10 false 2 2.073,1.063 2.229,1.26 0.156,0.198 10 false 1 2.073,2.781 2.229,2.979 0.156,0.198 10 false 2 2.063,3.427 2.219,3.625 0.156,0.198 10 false 1 1.76,2.771 2.073,2.969 0.313,0.198 10 false M+ 1.74,3.427 2.052,3.625 0.313,0.198 10 false M- 5.667,0.5 6.281,0.698 0.615,0.198 10 false VNM+ 5.677,1.167 6.292,1.365 0.615,0.198 10 false VNM- 5.448,0.354 5.604,0.552 0.156,0.198 10 false 6 5.375,1.031 5.74,1.219 0.365,0.188 10 false 25 5.458,2.76 5.615,2.958 0.156,0.198 10 false 7 5.406,3.427 5.771,3.615 0.365,0.188 10 false 26 5.677,2.885 6.292,3.083 0.615,0.198 10 false VN2+ 5.698,3.542 6.313,3.74 0.615,0.198 10 false VN2- 0.5,4.26 4.74,4.604 4.24,0.344 10 false DC Motor (Turbocharger Nozzle Vane Control Actuator Bank 2)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the turbocharger nozzle vane control actuator, initialize the learning values after replacement.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION

·

When replacing the turbocharger sub-assembly, calibrate the VN turbo offset voltage value and initialize the learning values after replacement.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P004518, P004519, P004600, P12A000, P12A018 AND/OR P12A019)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P004600 and/or P12A000 is output A
DTC P004518, P004519, P12A018 and/or P12A019 is output B
DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 and other DTCs are output C


HINT:

If codes other than DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

5.INSPECT VARIABLE VANE DC MOTOR (RESISTANCE)

C

GO TO DTC CHART

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE
a.

Loosen the installation bolt of the turbocharger nozzle vane control actuator.

A491960C01
0.323,0.396 0.635,0.552 0.313,0.156 10 false *1 4.125,0.406 4.438,0.563 0.313,0.156 10 false *2 0.531,0.667 0.844,0.823 0.313,0.156 10 true *3 1.719,0.927 2.031,1.083 0.313,0.156 10 true *4 0.969,0.844 1.281,1 0.313,0.156 10 true *3 1.406,0.625 1.719,0.781 0.313,0.156 10 true *3 5.781,0.833 6.094,0.99 0.313,0.156 10 true *3 6.281,1.031 6.594,1.188 0.313,0.156 10 true *3 6.74,0.813 7.052,0.969 0.313,0.156 10 true *3 5.156,0.906 5.469,1.063 0.313,0.156 10 true *4
*1 No. 1 Turbocharger Sub-assembly *2 No. 2 Turbocharger Sub-assembly
*3 Installation Bolt *4 E-washer



b.

Remove the e-washer from the turbocharger nozzle vane control actuator.


c.
A490876

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

4.REPLACE TURBOCHARGER SUB-ASSEMBLY
3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE TURBOCHARGER SUB-ASSEMBLY
HINT:

Replace the malfunctioning turbocharger sub-assembly.


a.

Replace the No. 1 turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


b.

Replace the No. 2 turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.INSPECT VARIABLE VANE DC MOTOR (RESISTANCE)
a.
C217215C05
0.12,0.111 0.297,0.288 0.177,0.177 10 *a
*a Component without harness connected
(Variable Vane DC Motor)


Disconnect the variable vane DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 1 to 100 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VARIABLE VANE DC MOTOR - ECM)

NG

10.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
6.CHECK HARNESS AND CONNECTOR (VARIABLE VANE DC MOTOR - ECM)
a.

Disconnect the variable vane DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C159,C138,C163)Location & Routing

Click Connector(C159)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>DC motor (Turbocharger Sub-Assembly)

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C163)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>DC Motor (No. 2 Turbocharger Sub-Assembly)

C159-1 (M-) - C138-25 (VNM-) Always Below 1 Ω
C159-2 (M+) - C138-6 (VNM+) Always Below 1 Ω
C163-1 (M-) - C138-26 (VN2-) Always Below 1 Ω
C163-2 (M+) - C138-7 (VN2+) Always Below 1 Ω
C159-1 (M-) or C138-25 (VNM-) - Body ground and other terminals Always 10 kΩ or higher
C159-2 (M+) or C138-6 (VNM+) - Body ground and other terminals Always 10 kΩ or higher
C163-1 (M-) or C138-26 (VN2-) - Body ground and other terminals Always 10 kΩ or higher
C163-2 (M+) or C138-7 (VN2+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo 1 and 2 Open.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo 1 and 2 Open
50004 372 102

e.

Maintain the Active Test "Activate the VN Turbo 1 and 2 Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.


f.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
NEXT



NEXT

END

10.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED