Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECM › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0492059 ECM A

F33A-FTV ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A495112N02
4.896,0.979 5.229,1.625 5.229,1.625 5.438,1.625 false 3.146,1.625 3.323,1.625 3.323,1.625 3.635,1.313 false 6.396,0.198 6.854,0.198 false 6.417,0.604 6.823,0.604 false 2.292,0.802 2.563,0.802 false 1.313,0.625 1.49,0.344 1.49,0.344 1.688,0.344 false 2.073,0.667 2.313,0.979 0.24,0.313 18 false 4 2.938,1.469 3.125,1.781 0.188,0.313 18 false 6 5.49,1.479 5.771,1.833 0.281,0.354 18 false 5 4.188,1.438 4.438,1.625 0.25,0.188 10 false x 2 5.521,1.021 5.781,1.219 0.26,0.198 10 false x 2 1.74,0.188 1.969,0.5 0.229,0.313 18 false 3 3.938,0.885 4.198,1.083 0.26,0.198 10 false x 2 6.219,0.052 6.5,0.406 0.281,0.354 18 false 1 6.229,0.458 6.51,0.813 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 AIR CLEANER ASSEMBLY 17730 - - -
4 ECM 89661A (Click here) - -
5 NO. 2 ECM BRACKET 89668A - - -
6 NO. 1 ECM BRACKET 89667A - - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

CAUTION / NOTICE / HINT

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
ECM The Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output w/ DPF:
(Click here)
w/o DPF:
(Click here)
·

Learning Values Save

·

Learning Values Write

·

VN Turbo Offset Voltage Value Compensation


·

Poor idle, etc.

·

Engine start function, etc.


Switch specification information Vehicle control history (RoB) [X263E] is stored w/ DPF:
(Click here)
w/o DPF:
(Click here)
Update ECU security key Vehicle control history (RoB) [XF01B] is stored (Click here)
Perform code registration Engine start See Service Bulletin for the registration method.

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 89661A 4.REMOVE ECM

a.
A486437N01
0.448,0.052 0.604,0.333 0.156,0.281 18 true ii 4.646,0.615 4.844,0.906 0.198,0.292 18 true iii 2.781,0.573 2.927,0.854 0.146,0.281 18 true i 4,0.031 4.229,0.323 0.229,0.292 18 true iv

i.

Detach the 2 clamps and remove the wiring harness protector.


ii.

Push each lever lock, raise each lever and disconnect the 3 connectors of ECM.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water and other foreign matter does not contact the connecting parts of the ECM connectors.



iii.

Detach the 3 wire harness clamps.


iv.

Remove the 3 bolts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89668A 5.REMOVE NO. 2 ECM BRACKET

A486359

Hide 89667A 6.REMOVE NO. 1 ECM BRACKET

A486360