Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P009511  Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Ground  P009515  Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A429908E03
3.49,2.656 4.125,1.854 4.125,1.854 4.302,1.854 true 2.208,0.813 3.281,1.01 1.073,0.198 10 false Resistance kΩ 3.292,4.365 5.302,4.552 2.01,0.188 10 false Temperature °C (°F) 4.365,1.76 5.896,1.958 1.531,0.198 10 false Acceptable 0.188,0.115 1.26,0.313 1.073,0.198 10 false (Fig. 1) 2.833,3.99 3.448,4.188 0.615,0.198 10 false (-4) 3.156,3.99 3.771,4.188 0.615,0.198 10 false (32) 3.729,3.99 4.344,4.188 0.615,0.198 10 false (104) 3.469,3.99 4.083,4.188 0.615,0.198 10 false (68) 4.042,3.99 4.656,4.188 0.615,0.198 10 false (140) 4.354,3.99 4.969,4.188 0.615,0.198 10 false (176) 4.667,3.99 5.281,4.188 0.615,0.198 10 false (212)

The Intake Air Temperature Sensor (for intercooler Inlet) detects the intake air temperature before the intake air passes through the turbo charger. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THCA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THCA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P009511 Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Ground Short in intake air temperature sensor (for intercooler inlet) circuit for 3 seconds.
(2 trip detection logic)
·

Short in intake air temperature sensor (for intercooler inlet) circuit

·

Intake air temperature sensor (for intercooler inlet)

·

ECM


Comes on SAE Code: P0097
P009515 Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open Open in intake air temperature sensor (for intercooler inlet) circuit for 3 seconds.
(2 trip detection logic)
·

Open in intake air temperature sensor (for intercooler inlet) circuit

·

Intake air temperature sensor (for intercooler inlet)

·

ECM


Comes on SAE Code: P0098

HINT:

When any of DTCs are stored, check the intake air temperature sensor (for intercooler inlet) by entering the following menus on the GTS: Powertrain / Engine / Data List / Intake Air Temperature B1S2.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
215°C (419°F) or more Short circuit

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P009511
P009515
Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A406114E12
0.448,2.813 1.385,3.052 0.938,0.24 10 false C114 5.563,3.01 6.021,3.208 0.458,0.198 10 false C138 5.563,3.188 6.021,3.385 0.458,0.198 10 false ECM 0.438,3.01 4.458,3.417 4.021,0.406 10 false Intake Air Temperature Sensor (For Intercooler Inlet) 5.26,1.333 5.719,1.531 0.458,0.198 10 false THCA 5.26,1.906 5.781,2.104 0.521,0.198 10 false ETCA 2.219,1.906 2.677,2.104 0.458,0.198 10 false 2 2.198,1.333 2.656,1.531 0.458,0.198 10 false 1 4.917,1.323 5.375,1.521 0.458,0.198 10 false 102 4.917,1.906 5.375,2.104 0.458,0.198 10 false 125 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R 1.906,1.333 2.365,1.531 0.458,0.198 10 false T3 1.844,1.906 2.302,2.104 0.458,0.198 10 false ET3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S2)
a.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.


b.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S2
50003 372 614

Standard:

Same value as the actual inlet air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) or more B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 215°C (419°F) or more.




A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A449482C18
0.458,3.271 0.938,3.573 0.479,0.302 1.271,3.99 1.542,3.552 true 2.115,4 1.865,3.563 true 2.677,1.396 2.99,1.594 0.313,0.198 10 false *2 2.448,0.656 2.958,0.865 0.51,0.208 10 false THCA 2.438,1.146 2.906,1.344 0.469,0.198 10 false ETCA 0.792,1.344 1.104,1.542 0.313,0.198 10 false *1 0.281,2.844 0.594,3.042 0.313,0.198 10 false *a 2.094,4.021 2.604,4.229 0.51,0.208 10 false T3 1.125,4.021 1.635,4.229 0.51,0.208 10 false ET3 0.542,3.333 0.948,3.552 0.406,0.219 10 false C114 1.74,0.667 2.25,0.875 0.51,0.208 10 false T3 1.719,1.052 2.188,1.25 0.469,0.198 10 false ET3
*1 Intake Air Temperature Sensor (For Intercooler Inlet)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (For Intercooler Inlet))


Disconnect the intake air temperature sensor (for intercooler inlet) connector.


b.

Connect terminals 1 (T3) and 2 (ET3) of the intake air temperature sensor (for intercooler inlet) wire harness side connector.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.


d.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S2
50003 372 614
OK:

215°C (419°F) or higher



e.

Reconnect the intake air temperature sensor (for intercooler inlet) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET) - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET)
a.

Replace the intake air temperature sensor (for intercooler inlet).

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET) - ECM)
a.

Disconnect the intake air temperature sensor (for intercooler inlet) connector.


b.

Disconnect the ECM connector.



d.

Reconnect the intake air temperature sensor (for intercooler inlet) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C65
0.667,0.156 0.938,0.365 0.271,0.208 10 false *1 2.573,0.156 2.875,0.458 0.302,0.302 10 false *2 2.427,1.063 3.063,1.219 0.635,0.156 10 false THCA 2.438,1.521 3.083,1.677 0.646,0.156 10 false ETCA
*1 Intake Air Temperature Sensor (For Intercooler Inlet)
*2 ECM


Disconnect the intake air temperature sensor (for intercooler inlet) connector.


b.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.


c.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S2
50003 372 614
OK:

-40°C (-40°F)



d.

Reconnect the intake air temperature sensor (for intercooler inlet) connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET)
a.

Replace the intake air temperature sensor (for intercooler inlet).

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 1 second or more.


d.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER INLET) - ECM)
a.

Disconnect the intake air temperature sensor (for intercooler inlet) connector.


b.

Disconnect the ECM connector.



d.

Reconnect the intake air temperature sensor (for intercooler inlet) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY