A thermistor is built into the engine coolant temperature sensor (for intercooler) and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P00DE11 | Charge Air Cooler Coolant Temperature Sensor Circuit Low Circuit Short to Ground | Short in the engine coolant temperature sensor (for intercooler) circuit for 3seconds or more. (1 trip detection logic) |
·
Short in engine coolant temperature sensor (for intercooler) circuit
·
Engine coolant temperature sensor (for intercooler)
·
ECM |
Comes on | SAE Code: P00E0 |
| P00DE15 | Charge Air Cooler Coolant Temperature Sensor Circuit High Circuit Short to Battery or Open | Conditions (a) and (b) continue for 3 seconds or more: (a) Intake air temperature is -30°C (-22°F) or higher. (b) Open in the engine coolant temperature sensor (for intercooler) circuit. (1 trip detection logic) |
·
Open in engine coolant temperature sensor (for intercooler) circuit
·
Engine coolant temperature sensor (for intercooler)
·
ECM |
Comes on | SAE Code: P00E1 |
| DTC No. | Data List |
|---|---|
| P00DE11 P00DE15 |
Intercooler Coolant Temperature |
If DTC P00DE11 and/or P00DE15 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P00DE11 and/or P00DE15 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine / Data List / Intercooler Coolant Temperature.
| GTS Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P00DE11 P00DE15 |
Ignition switch ON for 3 seconds or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Data List / Intercooler Coolant Temperature.
Read the value.
| Tester Display |
|---|
| Intercooler Coolant Temperature |
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| 70 to 90°C (158 to 194°F) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
Disconnect the engine coolant temperature sensor (for intercooler) connector.
| *1 | Engine Coolant Temperature Sensor (For Intercooler) |
*2 | ECM |
| *a | Front view of wire harness connector (to Engine Coolant Temperature Sensor (For Intercooler)) |
- | - |
Connect terminals 1 (E22) and 2 (THW2) of the engine coolant temperature sensor (for intercooler) wire harness side connector.
Enter the following menus: Powertrain / Engine / Data List / Intercooler Coolant Temperature.
Read the value.
| Tester Display |
|---|
| Intercooler Coolant Temperature |
140°C (284°F) or higher
Reconnect the engine coolant temperature sensor (for intercooler) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor (for intercooler).
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor (for intercooler) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C129,C138)Location & Routingewd_type=routing;type=c,c;code=C129,C138 |
||
| C129-2 (THW2) - C138-101 (THIW) | Always | Below 1 Ω |
| C129-1 (E22) - C138-124 (ETIW) | Always | Below 1 Ω |
Reconnect the engine coolant temperature sensor (for intercooler) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Engine Coolant Temperature Sensor (For Intercooler) |
| *2 | ECM |
Disconnect the engine coolant temperature sensor (for intercooler) connector.
Enter the following menus: Powertrain / Engine / Data List / Intercooler Coolant Temperature.
Read the value.
| Tester Display |
|---|
| Intercooler Coolant Temperature |
-40°C (-40°F)
Reconnect the engine coolant temperature sensor (for intercooler) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor (for intercooler) sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch to ON and wait for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor (for intercooler) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C129,C138)Location & Routingewd_type=routing;type=c,c;code=C129,C138 |
||
| C129-2 (THW2) or C138-101 (THIW) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the engine coolant temperature sensor (for intercooler) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT