Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P023A14  Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P023A12.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P023A12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023A14 Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open When the output duty of the electric water pump assembly is 30 to 85%, the IWPO output is continuously equal to or less than the judgment value for 3 seconds or more.
(1 trip detection logic)
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

ECM


Comes on SAE Code: P023B

Related Data List
DTC No. Data List
P023A14
·

Intercooler Water Pump Speed

·

Intercooler Water Pump



MONITOR DESCRIPTION

The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.

The electric water pump assembly is controlled steplessly by the drive duty signal (IWPO) output from the ECM.

The ECM monitors the actual drive duty cycle signal (IWPO) while simultaneously outputting the drive duty signal (IWPO) to the electric water pump assembly.

If the actual drive duty signal (IWPO) is less than or equal to the threshold value while the drive duty signal (IWPO) is being output to the electric water pump assembly, the ECM detects a malfunction and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P023A14 After fully warming up, increase and maintain the engine speed so that the intercooler water pump duty ratio is 30% or more for 3 seconds or longer.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Disconnect the electric water pump assembly connector.


b.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.


c.

Measure the resistance according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Control the Intercooler Water Pump
50004 372 9
Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-3 (SWP) - Body ground Before Active Test → Active Test in progress Before Active Test:
Resistance stabilized → Active Test in progress:
Resistance changes*



HINT:

*: The transistor inside the ECM is controlled by performing the Active Test.

The resistance of the SWP terminal changes while the Active Test is in progress due to duty control.

If the resistance fluctuates while the Active Test is being performed from the resistance that stabilized before the Active Test was performed, it can be judged that the transistor is operating.

If the transistor does not operate while the Active Test is being performed, the ECM may be malfunctioning.


Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29,B70)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B29-3 (SWP) - B70-37 (IWPO) Always Below 1 Ω
B29-3 (SWP) or B70-37 (IWPO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR