Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P040911  Exhaust Gas Recirculation Sensor "A" Circuit Short to Ground  P040915  Exhaust Gas Recirculation Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P040911 Exhaust Gas Recirculation Sensor "A" Circuit Short to Ground EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on SAE Code: P0405
P040915 Exhaust Gas Recirculation Sensor "A" Circuit Short to Battery or Open EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on SAE Code: P0406

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P040911
P040915
Ignition switch ON for 2 seconds or more

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C170,C138)Location & Routing

Click Connector(C170)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Electric EGR Control Valve Assembly

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C170-1 (VC) - C138-114 (VCEG) Always Below 1 Ω
C170-2 (VTA) - C138-67 (EGRA) Always Below 1 Ω
C170-3 (E2) - C138-113 (EEGL) Always Below 1 Ω
C170-1 (VC) or C138-114 (VCEG) - Body ground and other terminals Always 10 kΩ or higher
C170-2 (VTA) or C138-67 (EGRA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK ECM (EGR VALVE POSITION SENSOR VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM (EGR VALVE POSITION SENSOR VOLTAGE)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C170)Location & Routing

Click Connector(C170)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Electric EGR Control Valve Assembly

C170-1 (VC) - C170-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (CHECK RESISTANCE)

NG

5.REPLACE ECM
3.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C170)Location & Routing

Click Connector(C170)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Electric EGR Control Valve Assembly

C170-1 (VC) - C170-2 (VTA) Ignition switch off No short or no open circuit
C170-2 (VTA) - C170-3 (E2) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

5.REPLACE ECM
4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch to ON and wait for 2 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END