Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P040A11  Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low Circuit Short to Ground  P040A15  Exhaust Gas Recirculation Temperature Sensor "A" Circuit High Circuit Short to Battery or Open  


DESCRIPTION

The EGR gas temperature sensor is installed to the intake pipe between the electric EGR control valve assembly and intake manifold, and monitors the temperature of exhaust gas introduced into the intake manifold.

A thermistor built into the EGR gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The EGR gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the EGR gas temperature sensor from terminal THGO via resistor R.

Resistor R and the EGR gas temperature sensor are connected in series. When the resistance value of the EGR gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THGO also changes.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P040A11 Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low Circuit Short to Ground EGR gas temperature sensor output voltage is below 0.11 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in EGR gas temperature sensor circuit

·

EGR gas temperature sensor

·

ECM


Comes on SAE Code: P040C
P040A15 Exhaust Gas Recirculation Temperature Sensor "A" Circuit High Circuit Short to Battery or Open EGR gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in EGR gas temperature sensor circuit

·

EGR gas temperature sensor

·

ECM


Comes on SAE Code: P040D

Related Data List
DTC No. Data List
P040A11
P040A15
EGR Temperature B1S1

HINT:

When DTC P040A11 and P040A15 is output, check the exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1" using the GTS.

Reference:
Condition EGR Temperature B1S1 EGR Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
980°C (1600°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P040A11 Ignition switch ON for 3 seconds or more
P040A15 Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.

WIRING DIAGRAM

A445679E03
6.073,2.375 6.531,2.573 0.458,0.198 10 false ECM 6.063,2.208 6.521,2.406 0.458,0.198 10 false C138 5.688,0.615 6.146,0.813 0.458,0.198 10 false THGO 3.719,0.49 3.875,0.688 0.156,0.198 10 false 2 2.104,0.49 2.26,0.688 0.156,0.198 10 false 1 5.344,0.49 5.635,0.677 0.292,0.188 10 false 104 5.354,1.677 5.646,1.875 0.292,0.198 10 false 127 5.729,1.813 6.188,2.01 0.458,0.198 10 false ETGO 1.792,1.135 4.281,1.813 2.49,0.677 10 false EGR Gas Temperature Sensor 1.781,0.969 2.24,1.167 0.458,0.198 10 false C172 3.219,0.49 3.677,0.688 0.458,0.198 10 false THEG 2.354,0.49 2.813,0.688 0.458,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (EGR TEMPERATURE B1S1)
a.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1.

Powertrain > Engine > Data List
Tester Display
EGR Temperature B1S1
50003 372 1117

b.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
980°C (1600°F) or higher B
Same as the actual exhaust gas temperature C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 980°C (1600°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A494480C02
1.635,2.594 2.083,2.865 0.448,0.271 1.24,3.938 1.677,3.552 true 2.302,3.938 1.927,3.552 true 1.594,0.781 2.208,0.979 0.615,0.198 10 false THEG 1.635,1.448 2.25,1.646 0.615,0.198 10 false E2 0.115,0.125 0.427,0.323 0.313,0.198 10 false *1 2.01,0.125 2.323,0.323 0.313,0.198 10 false *2 0.135,2.594 0.448,2.792 0.313,0.198 10 false *a 1.719,2.688 2.125,2.844 0.406,0.156 10 false C172 2.26,3.958 2.667,4.115 0.406,0.156 10 false THEG 1.146,3.958 1.552,4.115 0.406,0.156 10 false E2
*1 EGR Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(EGR Gas Temperature Sensor)


Disconnect the EGR gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THEG) of the EGR gas temperature sensor connector on the wire harness side.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1.

Powertrain > Engine > Data List
Tester Display
EGR Temperature B1S1
50003 372 1117

d.

Read the value.

Standard:

980°C (1600°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE EGR GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EGR GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EGR GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EGR GAS TEMPERATURE SENSOR - ECM)

OK

5.REPLACE ECM

NG

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and turn the GTS on.


d.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 EGR Gas Temperature Sensor
*2 ECM


Disconnect the EGR gas temperature sensor connector.


b.

Enter the following menus: Powertrain / Engine / Data List / EGR Temperature B1S1.

Powertrain > Engine > Data List
Tester Display
EGR Temperature B1S1
50003 372 1117

c.

Read the value.

Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE EGR GAS TEMPERATURE SENSOR

NG

9.CHECK HARNESS AND CONNECTOR (EGR GAS TEMPERATURE SENSOR - ECM)
8.REPLACE EGR GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (EGR GAS TEMPERATURE SENSOR - ECM)

OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END